Fagor PL-1805 Manual De Instrucciones página 13

• Do not use the iron on very wet fabrics.
• Do not store the iron in a horizontal position (base
down) whilst still hot. Wait until it has cooled.
• Do not mix stain-removers or similar products on
fabrics to be ironed.
• Unplug the iron when not in use. Never leave plugged
in when not absolutely necessary.
• The appliance contains a safety device which, when
activated, interrupts the working of the iron. To
reactivate your iron, contact an authorised Technical
Assistance Service.
• If you decide never to use the appliance again,
remove the plug from the socket and render it
useless by cutting the power cable.
• La plancha se debe usar y colocar sobre una
superficie estable.
• Al colocar la plancha en su base de apoyo,
asegúrese de que la superficie es estable.
• La plancha no se debe utilizar si se ha caído, si tiene
signos visibles de daños o si pierde agua.
• Mantenga los aparatos eléctricos fuera del alcance
de los niños o personas enfermas. No les deje utilizar
los aparatos sin la supervisión de un adulto.
• El usuario no debe dejar la plancha desatendida
cuando esté enchufada a la toma de corriente.
• Se debe desenchufar de la toma de corriente antes
de llenar de agua el depósito.
• Este aparato no está diseñado para el uso de
personas (incluidos niños) con capacidades
físicas, sensoriales o mentales reducidas o falta de
experiencia y conocimiento, salvo que la persona
responsable de su seguridad les supervise o instruya
respecto al uso de aparatos.
• Se deberá vigilar a los niños para asegurarse de que
no juegan con el aparato.
• For greater protection, we recommend installing a
residual current device (RCD) with an operational
residual current not exceeding 30 mA. Ask your
installer for advice.
4. BEFORE USING YOUR IRON FOR
THE FIRST TIME
Remove all stickers or protective labels from the
base and the body.
Unroll and straighten the electrical cable.
Follow the instructions given in the "Self-
cleaning" section in point "10 – CLEANING", in
order to prepare your iron for use.
INSTRUCTIONS FOR USE
5. DRY IRONING
1. Place the iron on a stable and heat-resistant
surface.
2. Turn the temperature selector knob (2) to MIN
(Fig. B).
3. Slide the steam control knob (7) to the dry iron
position (Fig. C).
4. Place the iron in an upright position, resting it on
the support base (10).
5. Plug it in and turn the temperature selector to the
desired position. The pilot light (4) will come on.
6. When the iron has reached the selected
temperature, the pilot light (4) will switch off.
This pilot light may turn on and off several times
while you are ironing, indicating the cycles of the
thermostat. Remember that if you change from
a higher to a lower temperature, the pilot light (4)
will remain off until the temperature of the base
(1) has dropped to the selected level, at which
point it will come on again.
7. When you have finished, turn the temperature
selector to MIN and unplug the iron. Leave to
cool before cleaning the exterior and storing.
When you are dry ironing, you can use the spray
option at any moment, providing there is water in
the deposit. (See sections entitled "Spray" and
"Filling the deposit").
6. FILLING THE WATER DEPOSIT
Place the unplugged iron on a stable surface.
1. Slide the steam control knob (7) to the dry iron
position (Fig. C).
2. Open the lid that covers the water inlet (5).
3. Slowly pour water into the inlet using a cup (Fig.
D). Never pour cleaning products or solvents into
the water deposit.
4. Check that the water does not exceed the
maximum water level and replace the cover.
Note: If the water in your area is too hard, >27º F,
we recommend that you use distilled water. Do
not use battery water or water mixed with starch,
perfume, fabric softener, etc.
7. STEAM IRONING
Before steam ironing any garment, check that
the fabric is designed for this kind of treatment.
The appliance works with normal tap water. If
the water in your area is very hard (hardness
12