RIDGID 45178 Manual Del Usuario página 6

700 Power Drive
• When threading 1" (25mm) or larger pipe, use
sup port device to resist threading forces. Use an
appropriate support device per these instructions.
Support devices improve control and reduce the risk of
striking, crushing, and/or other injuries.
• When using a support device other than the support
arm, the support device must react against the
motor housing. Support devices contacting other parts
may damage the machine parts or increase the risk of
injury.
• Always firmly hold the power drive when threading
or backing die head off the pipe to resist threading
forces, regardless of support device use. This will
reduce the risk of striking, crushing and other injuries.
• Do not use this power drive if switch button is
broken. This switch is a safety device that lets you shut
off the motor by releasing the switch.
• Do not wear gloves or loose clothing when oper-
ating machines. Keep sleeves and jackets but-
toned. Do not reach across the machine or pipe.
Clothing can be caught by the pipe or machine result-
ing in entanglement.
• One person must control the work process and
machine operation. Only the operator should be in the
work area when the machine is running. This helps
reduce the risk of injury.
• Do not use dull or damaged dies. Sharp cutting tools
require less torque and the power drive is easier to
control.
• Keep handles dry and clean, free from oil and
grease. Allows for better control of tool..
• Keep floors dry and free of slippery materials
such as oil. Slippery floors invite accidents.
• Only use RIDGID die heads with RIDGID 700 Power
Drive, other die heads may not fit correctly in the
power drive increasing the risk of equipment dam-
age and personal injury.
• When using for applications other than described
in this manual, use a support device to resist han-
dle forces. Support devices improve control and reduce
the risk of striking, crushing, and/or other injuries.
If you have any question concerning this RIDGID
– Contact your local RIDGID
– Visit RIDGID.com to find your local RIDGID contact
point.
– Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com, or in the U.S. and
Cana da call (800) 519-3456.
4
® product:
® distributor.
description, Specifications
And Standard equipment
description
The RIDGID ® Model 700 Power Drive is designed to pro-
vide power for threading pipe and conduit. Forward and
Reverse rotation can be selected with a reversible switch.
The power drive is designed to use RIDGID 12-R Die
Heads (1/8 – 2 pipe). Other RIDGID die heads such
as the OO-R and 11-R can be used with adapters.
When threading 1" or larger pipe, a support device, such as
the No. 775 Support Arm or a RIDGID 14" heavy duty pipe
wrench is required to resist the threading forces.
The power drive can also be used to power the RIDGID 258
Pipe Cutter and for other applications, (See "Other Uses").
Switch Motor
Serial Number
Housing
Button Plate
Handle
Brush Cap
Torque
Arm
Figure 1 – Model 700 Power Drive
Specifications
Threading Capacity ....Pipe
Bolt
00-RB Die Head
Motor*:
Type .........................Universal, Reversible
Volts .........................110
Amps ........................13.5
Frequency ................50/60 Hz 50/60 Hz 50/60 Hz
Power .......................1500
Operating Speed........26-30 RPM, No load
Controls......................Double-Throw Reversible
Switch with spring return to OFF
position
Gear Head .................Die Cast Aluminum, Spur Gear
Reduction Face Gear Drive,
Spring-Loaded Adapter Pawls,
Hardened Steel Spindle Gear
Dimension:
Length ......................28¼" (717 mm)
Width........................6 1 /
16
Warning Label
(on Motor Housing)
Grease
Fitting
Handle
Gear
Case
Fan
Housing
Adapter
Pawl
1 / " to 2" (3 to 50 mm)
8
1 / " to 1" (6 to 25 mm) with
4
120 220-240
13.5 6.5
1500 1500
" (154 mm)
940-707-010.09_REV. F