Remoset Function - Monacor International JTS UF-20S/5 Manual De Instrucciones

Receptor de banda ancha true diversity
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5) Press the knob once again so that the digits
before the decimal point are selected Turn
the knob to set the transmission frequency
in steps of 1 MHz
6) For fine adjustment in steps of 0 025 MHz,
press the knob once again so that the digits
after the decimal point are highlighted Then
turn the knob
7) Press the button SETUP to save the frequency
selected
8) To save further frequencies, repeat steps 2 – 7
9) To exit all menus, press the button EXIT three
times
– Calling up a channel
from a user-defined group –
The channels from user-defined groups are called
up via the menu item
described in chapter 3 5 2 User- defined groups
are marked with the letter
number When the knob PUSH /CONTROL is
turned clockwise, they will appear after group
15; when it is turned counter-clockwise, they
will appear before group 1
– Deleting a user-defined group –
1) Call up the following submenu via the menu
item
3. User Group
1. Custom Groups
2. Clear Group
3. Return
2) Turn the knob PUSH  /CONTROL to select the
second menu item
press the knob:
Group:
U1
Rotary to select
Push "Enter" to clear
Push "Exit" to return
3) Turn the knob to select the group to be de-
leted Then press the knob The following
confirmation prompt appears:
Group "Ux" will be cleared
continues?
Yes
No
4) To exit, press the knob or the button EXIT To
delete the group, turn the knob so that
is selected Then press the knob
5) To delete further groups, repeat steps 3 – 5;
to exit all menus, press the button EXIT three
times
2. Group/Channel
preceding the group
U
of the main menu:
Fig. 19
Then
Clear Group
Fig. 20
Fig. 21

3.5.5 REMOSET function

Transferring settings to the transmitter
If the transmission frequency or the group and
the transmission channel have been set on the
receiver, simply press a button to activate the
patented REMOSET function which will transfer
the settings of the receiver to the corresponding
transmitter (wireless microphone /pocket trans-
mitter) For the REMOSET function always make
sure that
1 no menu is called up on the receiver or on
the transmitter
2 the transmitter is switched on and close to
the receiver (REMOSET transmission range:
approx 10 m)
3 the REMOSET function is not disabled on the
transmitter (
as
4 the transmitter and the receiver are set to the
same identification number
5 the receiver and the transmitter are not
locked
6 the transmitter is not muted
– Identification number –
To prevent mutual interference of individual
pairs of transmitter / receiver during REMOSET
transmission, each pair must have a different
identification number (ID No ) If only one pair of
transmitter / receiver is used, there is no need to
change the preset ID No 1 To change the ID No :
1) Call up the setting for the ID No via the menu
item
6. Device ID
Setup Device ID
1
[0~255]
2) Press the knob PUSH  /CONTROL to set the
ID No
3) Press the button SETUP to save the setting
4) Press the button EXIT to exit the main menu
5) Set the transmitter to the same ID No
– REMOSET transmission –
YES
Press the button REMOSET (3) During the
REMOSET transmission, the button keeps flash-
ing rapidly As soon as the settings have been
transferred to the corresponding transmitter, the
button lights permanently
manual of the transmitter)
of the main menu:
Fig. 22
21

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jts uf-20r /5

Tabla de contenido