Renfert Waxlectric I Instrucciones De Servicio página 11

↔
Switch between o C o F:
Only possible when switching on !
Please observe that all
230 V units are pre-set
to centigrade (°C) and
Hold for
all 120 V units are pre-
5 sec. !
set to Fahrenheit (°F).
↔
C F
Setting the temperature:
↑ ↑ ↑ ↑ ↑
= Temp.
↓ ↓ ↓ ↓ ↓
= Temp.
Speed setting to maximum temperature
(Waxlectric II version only possible at
the right channel):
Switch off !
+
Press and
Switch
hold !
on
→
2 0 0
= O C
→
3 9 2
= O F
Speed setting to minimum temperature
(Waxlectric II version only possible at
the right channel):
Switch off !
+
Press and
Switch
hold !
on
→
5 0
= O C
→
1 2 2
= O F
4.3 Changing the tips:
Take care when changing the
tips. They may still be hot !
Make sure the O-ring is present
(ill. 6) - it is the seal against
wax penetration !
→
see illustrations 5, 6, 7, 1
4.4 Changing the cork:
→
see illustrations 5 + 8
5. Areas of Caution
• Before switching on check that
the unit's voltage matches the
main power supply.
• Units with faulty leads or other
defects should not be used.
• Do not cover the power units
when in use.
• Unroll power supply cable
(overheating may occur in
event of short circuit).
• The tips of the waxing-up in-
strument reach a working tem-
perature of 200°C [392°F].
> Improper use may lead to a
danger of burning!
• The red marked end of the
handle of the instrument gets
very hot while working.
> Improper use may lead to a
danger of burning!
↔
Switch between o C o F:
Only possible when switching on !
Please observe that all
230 V units are pre-set
to centigrade (°C) and
Hold for
all 120 V units are pre-
5 sec. !
set to Fahrenheit (°F).
↔
C
F
Setting the temperature:
↑ ↑ ↑ ↑ ↑
= Temp.
↓ ↓ ↓ ↓ ↓
= Temp.
Speed setting to maximum temperature
(Waxlectric II version only possible at
the right channel):
Switch off !
+
Press and
Switch
hold !
on
→
2 0 0
= O C
→
3 9 2
= O F
Speed setting to minimum temperature
(Waxlectric II version only possible at
the right channel):
Switch off !
+
Press and
Switch
hold !
on
→
5 0
= O C
→
1 2 2
= O F
4.3 Changing the tips:
Take care when changing the
tips. They may still be hot !
Make sure the O-ring is present
(ill. 6) - it is the seal against
wax penetration !
→
see illustrations 5, 6, 7, 1
4.4 Changing the cork:
→
see illustrations 5 + 8
5. Areas of Caution
• Before switching on check that
the unit's voltage matches the
main power supply.
• Units with faulty leads or other
defects should not be used.
• Do not cover the power units
when in use.
• Unroll power supply cable
(overheating may occur in
event of short circuit).
• The tips of the waxing-up in-
strument reach a working tem-
perature of 200°C [392°F].
> Improper use may lead to a
danger of burning!
• The red marked end of the
handle of the instrument gets
very hot while working.
> Improper use may lead to a
danger of burning!