Publicidad
Idiomas disponibles
Idiomas disponibles
English
Cleaning
WARNING:
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Cleaning/Emptying the Dust Bowl and
Filters (Fig. C, G–H)
WARNING:
Never use the vac without its filter.
nOTE: The filter is re‑usable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
Removing Pre‑Filter
1. Place the vacuum over a trash bin and remove the
dust bowl
3
from the main housing by pressing the
dust bowl release button
the dust bowl by pulling the dust bowl away from the
main housing.
2. Remove the filter assembly
dust bowl.
3. Twist counterclockwise and pull the pre‑filter
seperate it from the filter
4. Remove the pre‑filter and shake or lightly brush any dust
from the filter and pre‑filter.
5. Empty any dust from the dust bowl
and wash if necessary. Ensure that the dust bowl is
completely dry before using.
6. Wash the pre‑filter
10
warm, soapy water. Ensure that both are completely dry
for 12 hours before using.
7. Install the pre‑filter onto the filter, ensuring the filter
tabs
12
aligns with the pre‑filter slots
pre‑filter clockwise to lock it firmly into position.
8. Install the filter assembly into the dust bowl.
9. Install the dust bowl onto the main housing and lock it
firmly into position.
8
Blow dirt and dust out
Never use solvents or other
Projectile/Respiratory Hazard:
2
on the handle and remove
4
by pulling it out of the
10
11
.
3
into a trash bin
and filter
11
regularly using
13
and rotate the
Cleaning the Filter
iMPORTAnT: Maximum dust collection will only be
obtained with a clean filter and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
1. Once the filter and pre‑filter are removed from the
dust bowl shake off or lightly brush any dust from the
pre‑filter
2. Rinse out the dust bowl with warm soapy water.
3. Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
4. It is very important that the filters are completely dry and
correctly in position before use.
5. Ensure the filters are completely dry for 12 hours
before refitting.
6. Follow instructions in the Removing Pre‑Filter section
for assembly instructions.
Accessories
WARNING:
those offered by BLACK+DECKER, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
BLACK+DECKER recommended accessories should be
used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact BLACK+DECKER call 1‑800‑544‑6986.
Replacing the Filters
The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
to
available from your BLACK+DECKER dealer.
Visit www.blackanddecker.com to locate dealers.
Remove the old filters as described in Cleaning/
•
Emptying the Dust Bowl and Filters.
•
Fit the new filters as described in Cleaning/Emptying
the Dust Bowl and Filters..
•
Only use BLACK+DECKER replacement filter: HLVCF10
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING:
and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a BLACK+DECKER
factory service center or a BLACK+DECKER authorized
service center. Always use identical replacement parts.
10
and filter
11
.
Since accessories, other than
To assure product SAFETY
Publicidad
