tau ARM200 Manual De Uso Y Mantenimiento página 13

DESCRIPTION
The ARM200 automated system for swing gates is an electro-me-
chanical non-reversing actuator that transmits motion to the leaf
via a worm screw system.
The actuator is available in more versions in 18V DC and 230V AC.
The non-reversing system ensures the leaf is mechanically locked
when the motor is not operating, but it is not intended as a high
degree security deterrent against intrusion attempts and/or tam-
pering. A convenient and safe release system with customised key
makes it possible to manually move the leaf in the event of a mal-
function or of a power failure.
ATTENTION:
The correct operation and the declared specifica-
tions only apply if TAU accessories and safety de-
vices are used.
In the absence of a mechanical clutch, the use of
a control unit with an adjustable electronic clutch,
or the installation of a sensitive edge, is required in
order to ensure crush-proof safety.
The ARM200 automated system was designed and
built for controlling vehicle access. It is not intend-
ed as a high degree security deterrent against in-
trusion attempts and/or tampering. Avoid any other
use whatever.
ACTUATOR PARTS (fig.1)
Pos. Description
1 Actuator
2 Release device
3 Rod
4 Wing connection bracket
5 Rear bracket
6 Terminal board cover
DIMENSIONS (fig.2)
INSTALLATION (fig.3)
Electrical set-up (standard system - ARM200)
Pos. Description
1 Attuatore
2 Control unit
3 TX photocells
4 RX photocells
5 Key-operated selector switch
6 Flashing light and aerial
7 Mechanical stops
Electrical set-up (standard system - ARM200BENC)
Pos. Description
1 Attuatore
2 Control unit
3 TX photocells
4 RX photocells
5 Key-operated selector switch
6 Flashing light and aerial
7 Mechanical stops
Notes:
• Use suitable tubes and/or hoses to lay electric cables
• Choose short routes for cables and keep power cables sepa-
rate from control cables.
Preliminary checks
Prior to installing the automation, make all structural modifications
in order to ensure safety distances and protect and segregate ar-
eas in which people may be exposed to the risk of crushing, shear-
ing, dragging or similar dangers.
• Make sure the existing structure is sufficiently sturdy and sta-
ble;
• the mechanical parts must conform to the provisions of Stand-
ards EN 12604 and EN 12605;
•
•
•
•
•
Perform any necessary metalwork job before installing the auto-
mated system.
The condition of the gate structure directly affects the reliabil-
ity and safety of the automated system.
Installation dimensions (fig.4)
Determine the fitting position of the actuator with reference to fig.4.
Check with care if the distance between the open leaf and any ob-
stacles (walls, fences etc.) is higher than the actuator dimensions.
Cables
4x1,5 mm²
3x1,5 mm²
(power supply)
4x0,5 mm²
2x0,5 mm²
3x0,5 mm²
2x1 mm² + 1RG58
-
Cables
2x2,5 mm² + 3x0,5 mm²
3x1,5 mm²
(power supply)
4x0,5 mm²
2x0,5 mm²
3x0,5 mm²
2x1 mm² + 1RG58
-
ARM200 Series
leaf length in compliance with the actuator specifications;
regular and uniform movement of the leaves, without any fric-
tion and dragging during their entire travel;
stiff hinges in good conditions;
presence of both opening and closing mechanical limit stops;
presence of an efficient earthing for electrical connection of the
actuator.
ARM225I
X° A (mm)
90 110
90 115
90 120 ÷ 125
90 130
90 135
90 140
90 145
90 150 ÷ 155
90 160
90 165
100 130
100 135
ARM250I
X° A (mm)
90 120 ÷ 125
90 130
90 135
90 140
90 145 ÷ 150
90 155
90 160
90 165
90 170 ÷ 175
90 180
90 185
90 190 ÷ 195
90 200
100 145
100 150
100 155
100 160
100 165
100 170
100 170
100 180
100 185
100 190
100 195
100 200
110 170
110 175
110 180 ÷ 185
110 190
110 195
110 200
B (mm) C (mm)
120 ÷ 165 20 mm
120 ÷ 160 20 mm
120 ÷ 155 20 mm
120 ÷ 150 20 mm
120 ÷ 145 20 mm
120 ÷ 140 20 mm
120 ÷ 135 20 mm
120 ÷ 130 20 mm
120 ÷ 125 20 mm
120 ÷ 120 20 mm
120 ÷ 130 20 mm
120 ÷ 120 20 mm
B (mm) C (mm)
135 ÷ 275 20 mm
135 ÷ 270 20 mm
135 ÷ 265 20 mm
135 ÷ 260 20 mm
135 ÷ 255 20 mm
135 ÷ 250 20 mm
135 ÷ 245 20 mm
135 ÷ 240 20 mm
135 ÷ 235 20 mm
135 ÷ 230 20 mm
135 ÷ 225 20 mm
135 ÷ 220 20 mm
135 ÷ 215 20 mm
135 ÷ 160 20 mm
135 ÷ 210 20 mm
135 ÷ 225 20 mm
135 ÷ 220 20 mm
135 ÷ 215 20 mm
135 ÷ 210 20 mm
135 ÷ 205 20 mm
135 ÷ 200 20 mm
135 ÷ 195 20 mm
135 ÷ 190 20 mm
135 ÷ 185 20 mm
135 ÷ 180 20 mm
135 ÷ 140 20 mm
135 ÷ 155 20 mm
135 ÷ 175 20 mm
135 ÷ 165 20 mm
135 ÷ 160 20 mm
135 ÷ 155 20 mm
13