Publicidad
Idiomas disponibles
Idiomas disponibles
EN
1 Filter strainer cover
2 Dust container button
3 Wall sensor
4 System reset button
5 System upgrade connection
(this connection is for professional use only)
Docking station
1 Power indicator light
2 Signal transmission area
3 Base charging contacts
4 Catch groove
5 Cover plate
6 Cable passage
7 AC adapter socket
8 Winding pin
List of parts
1 Docking station 1x
2 Remote control 1x
3 Wiping cloth 2x
4 HEPA filter + foam filter 3x
5 Adapter 1x
6 Cleaning brush 1x
7 Left and right brush 2x
8 Main brush cover with steel wire 1x
1
2
3
76
1
2
1
2
3
6
4
5
4
7
5
8
6
KEY FEATURES
Cleaning / ON/OFF
• Press briefly to start or pause cleaning.
3
• Press and hold for 3 seconds to switch the appliance
on or off.
• Long press for 15 seconds to force the appliance to
shut down under unusual circumstances.
4
Charging / Local cleaning
• Press briefly to start or pause charging.
5
• Long press to start local cleaning.
Indicator light
• Turquoise: Normal operation or charging.
• Red: Abnormal condition or low battery.
• Light blue: The appliance is not connected to the
network.
Wi-Fi reset
7
• Press both buttons simultaneously for 3 seconds.
INSTALLATION
8
1. Connect the power cord and store the excess
cable length in the cable compartment.
2. Place the docking station against the wall and
connect the power.
Note:
• Provide a space of min. 0.5 m on both sides of the
docking station and min. 1.5 m in front of the station.
• If the power cord is stretched vertically to the ground,
the appliance may pull it out and the docking station
may be switched off.
• In normal condition, the charging indicator light is on
when switched on. When the appliance is charged, the
indicator remains lit.
3. Do not move the docking station or expose it to
direct sunlight.
Note: Direct sunlight will interfere with the docking
station signal and the appliance may not return to the
docking station properly.
4. Installing the side brush
Make sure the left side brush (L) and right side brush
(R) markings correspond to the L and R markings on
the bottom cover. Push the side brushes L and R until
you hear a "click" sound.
5. Putting the appliance into operation and charging
To switch the robot on, press and hold the button
If the power indicator light is normally on, charge the
robot in the docking station.
Note: If the appliance does not start due to a low
battery, charge it in the docking station and it will start
automatically. Normally, the appliance can only operate
when the battery level is ≥15 %.
VR3105
VR3105
6. Connecting a mobile app (you can skip this step)
Read the instructions for connecting Wi-Fi and connect
the mobile app.
7. Start of cleaning
After switching on the robot, briefly press the button
on the robot or start cleaning using the mobile app
(you can pause the appliance by pressing any button
during use).
Note:
• The sweeping robot cannot be used to remove fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
appliance catches these wires.
• Do not carry the robot during operation. Always use
the manual control designed for controlling the robot.
USE
ON/OFF
Press and hold the button
for 3 seconds, the indicator
light comes on and the appliance starts.
Press and hold the button
for 3 seconds while the
appliance is in standby mode, the indicator light goes out
and the appliance switches off.
NOTE: The appliance cannot be switched off while it is
being charged.
CLEANING/PAUSE
After starting the appliance, briefly press the button
the appliance or start the appliance using the mobile app
(press any button to pause the appliance).
Note:
• The robotic vacuum cleaner cannot be used to remove
fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
.
robot catches these wires.
CHARGING
Automatic mode: The appliance automatically returns to
the docking station after work.
Manual mode: When paused, press the button
to start charging or you can use your mobile app to
EN
on
briefly
77
Publicidad
