Tecfrigo SNELLE 750 RBT Instalación Y Uso página 7

8. CONTROLS
The controls of the appliance are situated at the front inside a protected recess.
1. Refrigeration switch
for turning on the refrigeration system.
inside the appliance. 3. Rotation switch:
reading the temperature in the appliance.
adjust the temperature: a) Press key
set-point. Press key 6 "UP"
lights, turn on the relevant switch. To activate the rotary shelves, turn on the relevant switch, taking into
account that shelves will only rotate if the door is closed. For safety reasons, rotation stops when the door
is opened or if even the slightest obstruction is encountered.
switch for turning on the refrigeration system.
appliance. 8. Ventilation switch:
over 0°C. 4. Thermomete
temperature in the appliance. Press key
can be modified by pressing key
9. CHECKING CORRECT OPERATION
Make sure that: 1.
the plug is connected; . the refrigeration unit switch is turned on (green light lit up);
3 . thermometer shows the desired temperature for the goods to be stored; . rotation system and lights
are turned on; . door is firmly closed; . appliance is not exposed to direct sunlight or to powerful lamps; 5
7. ambient temperature does not exceed +30°C with 55% R.H. (climatic class 4); . there is sufficient
ventilation for the motor compartment; there is a clearance of at least 30 cm in front of the grill; . the
cabinet is suitably filled and shelves not overloaded (max. 6 kg per shelf); there are sufficient gaps inside
the cabinet to enable cold air to circulate, especially between the rear glass panel and the shelves in the
area near the air outlets.
10. INTERNAL CLEANING (EVERY 15 DAYS)
1 . Switch off the appliance. . Open the door and remove the refrigerated goods.
surfaces of the appliance with a sponge dipped in water with a little sodium bicarbonate. Dry with care.
11. REPLACEMENT OF INTERNAL LIGHT BULBS
1. Switch off the appliance.
fluorescent tube with its protective cover from the top lamp socket.
5.
lamp socket. Remove the protective cover. . Replace the fluorescent tube.
the above instructions in reverse order (see fig.8).
12. REPLACEMENT OF THE DOOR'S MAGNETIC GASKET
1 . Open the door. 2 . Take hold of the magnetic gasket with your hands and pull it out of the frame.
3. Insert the new gasket and press it firmly down all around (see fig.9).
13. REPLACEMENT OF A GLASS PANEL
1. Switch off the appliance. . Undo the screws attaching the door hinges to the frame and remove the
3.
door. Remove both the internal and external screws of the upper corner mountings.
corner mountings by sliding them upwards. . Remove the glass panel by sliding it upwards. . Replace
with a new glass panel (see fig. 10).
Operator's guide
it sets the rotary shelves into motion.
Thermostat
5 "SET" (once only) and the display will show the cell's temperature
to increase temperature or key
2. Light switch
this should be turned to II if the appliance is working at a temperature of
r for reading the temperature in the appliance.
5 "SET or P
6 "UP" or 7 "DOWN".
2
6
2
2. Undo the screws which hold the top lamp socket in place. . Detach the
6
2
5
7
2. Light switch
for adjusting temperature in the appliance. To
7 "DOWN" to reduce. To turn on the internal
400 BTV model only: 1. Refrigeration
for turning on the light inside the
Thermostat
" once to display the temperature set-point, which
(see fig.7)
4
4. Take the tube out of the bottom
7.
for turning on the light
4. Thermomete r for
for adjusting
8
9
3 . Wipe the internal
3
Reassemble by following
4.
Remove the
6
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO