Metabo 613088800 Manual Original página 10

en ENGLISH
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 LED lights
2 Release lever
3 Slide switch
4 Handle
5 Setting wheel for speed adjustment
6 Button of capacity display*
7 Capacity and signal display*
10
8 Battery pack *
9 Battery pack release button
10 Accessory*
11 Dust extraction*
12 Extraction adapter*
13 Depth guide*
14 Allen screw 1
15 Allen screw 2
16 Screwdriver for Allen screw*
17 Housing flange
18 Tool holder
19 Saw blade
20 Spring pin
21 Sanding plate
*depends on features / model
6. Commissioning
Battery pack
Charge the battery pack (8) before use.
If performance diminishes, recharge the battery
pack.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Li-Ion battery packs "Li-Power" have a capacity and
signal indicator (7):
- Press the button (6), the LEDs indicate the charge
level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the battery pack
Removing the battery pack
Press the battery pack release (9) button and
remove the battery pack (8).
To fit
Slide in the battery back (8) until it engages .
7. Use
7.1 Attach dust extraction (only when working
with triangular sanding plate)
See fig. 1 and 2, page 2
- Remove the accessory.
- Put the dust extraction (11) on the housing flange
(17) and fix with screwdriver (16) and screw (15)
in the desired position:
- Connect a suitable extraction device with its
suction hose to the inserted suction adapter (12).
7.2 Attaching the accessory
Prior to any conversion work: remove battery
pack from machine.
Danger of injury due to the sharp accessories.
After stopping work, the tool may still be hot.
Danger of crushing when changing the tool. Wear
protective gloves.