Metabo W 8-115 Instrucciones De Manejo página 12

17026938_1009 kl WS W 8_115 ff NAFTA Protect.book Seite 12 Mittwoch, 21. Oktober 2009 4:34 16
ENG ENGLISH
8.3 Working instructions
Grinding:
Press down the machine evenly on the surface
and move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of
30° - 40° for the best working results.
Separating:
Always work against the run of the
disc (see illustration). Otherwise
there is the danger of the machine
kicking back from the cut out of
control. Guide the machine evenly at
a speed suitable for the material being processed.
Do not tilt, apply excessive force or sway from side
to side.
Sanding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
9 Cleaning
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
10 Troubleshooting
Machines with VTC and TC electronics
(not WE 14-125 VS):
The electronic signal display (6) lights up
and the load speed decreases. The coil
temperature is too high! Run the machine
in idling until the electronics signal indicator
switches off.
Machines with VTC, TC, VC and C electronics:
The electronic signal display (6) flashes
and the machine does not start. The
restart protection is active. If the mains plug
is inserted with the machine switched on, or if the
current supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
11 Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
12
All manuals and user guides at all-guides.com
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
A Roughing disc (always use with safety guard
attached)
B Louver disc (always use with safety guard
attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with parting safety
guard attached)
F Cup wheel guard (place on machine and
secure with screws (f)). Secure cup wheel as
described in chapter 7. Use an offset 2-hole
spanner if necessary. Use the wing screws to
adjust the safety guard until the cup wheel
protrudes between 0.5 cm - 1 cm.
G Cup wheels (always use with cup wheel safety
guard attached)
H Offset 2-hole spanner (for securing/loosening
the clamping nut (13) on cup wheels)
I Parting safety guard with guide slot (place on
machine and secure with screws.) (with
adapter for connection to a suitable dust
extractor for extraction of stone dust gener-
ated when cutting stone slabs.)
J Hand guard (for attaching under the additional
side-mounted handle.)
K Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx.
35 mm)
L Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
M Fibre discs (always use with the hand guard
attached.)
N Semi-flexible sanding discs (for use with
elastic supporting disc 6.23279) (always use
with hand guard attached.)
O Sanding pad with Velcro (always use with the
hand guard attached.)
P Adhesive sanding disc (always use with the
hand guard attached.)
Q Adhesive fleece (always use with the hand
guard attached.)
R Steel wire brushes (always use with the hand
guard attached.)
S Supporting flange for type 27 wheels 6"
diameter
T Adjusting nut (13)
U "Quick" clamping nut (1)