Publicidad
Idiomas disponibles
Idiomas disponibles
EN
IMPORTANT ADDITIONAL INFORMATION
IMPORTANT
MANUFACTURING LABEL CAN BE FOUND STAMPED IN THE MOTOR CASE IN BACK
OF THE TOILET. PLEASE GATHER INFORMATION TO REGISTER PRODUCT FOR
WARRANTY PURPOSES BEFORE INSTALLING AND SECURING TOILET TO THE FLOOR.
GENERAL DESCRIPTION
I
Th e S a n i co m p a c t ® 4 C i s a
combination of a floor-mounted
vitreous china toilet with a built-in
macerating and pump system.
The Sanicompact® 4C is meant to be
installed in residential applications
and can be adapted to discharge
gray water from a sink.
The Sanicompact® 4C is comprised
of two major components: the china
toilet body and the macerating/
pump unit in the base of the toilet.
NORMAL OPERATING CYCLE
Sanicompact® 4C is controlled by
an electronic program with two
functions.
It has a macerating and pumping
•
function. To begin press on either
side of the push button (light
grey: small flush, dark grey: large
flush) integrated to the bowl.
The pump cycle cleans the
•
washbasin waste. This is an
automatic operation that will
activate as long as water from
the washbasin enters the unit.
LIST OF PARTS SUPPLIED
II
See page 3.
DIMENSIONS
III
See page 15.
PERFORMANCE CURVE
IV
AND TECHNICAL DATA
See page 16.
APPLICATION
Maximum vertical
pumping
Voltage
Frequency
Normal power rating
Maximum current
consumption
Maximum water
temperature
Electric class
Degree of protection
Net weight
Horse power
WARNING: Only installations
c o n f o r m i n g
specifications are acceptable.
V
INSTALLATION
ATTACHING THE TOILET TO
V.1
THE FLOOR (see fig. 5)
After installing the water supply
1.
line and the drain hose, place the
Sanicompact® 4C so that it is
aligned with the piping.
Mark the fixing holes of the
2.
bowl on the floor.
Remove the device.
3.
If the unit is installed on a
4.
concrete or stone floor, drill two
5/16 inch holes (8 mm) at a depth
of about 2 inches (50 mm) and
insert the dowels. In the case of
installation on a wooden floor, drill
a guide hole for # 10 wood screws.
Make the water connections.
5.
Place the Sanicompact® 4C.
6.
Fix the Sanicompact® 4C to the
7.
floor with the screws.
Do not over tighten the screws as
the porcelain base may crack.
CONNECTION OF THE
V.2
DISCHARGE ELBOW (see fig. 2)
Fully insert the elbow
1.
end of the rubber waste tube,
after turning it to face in the
desired direction.
Fix the base of the elbow
2.
tighten it on the rubber waste
tube with a clamp
Connect the sleeve
3.
of the elbow with the clamp
1 WC + sink
Connect the 1" wastepipe into
4.
9 feet
the sleeve and secure with clamp
WARNING: Ensure that you do not
110-115 V
twist the discharge pipework inside
60 Hz
the unit.
815 W
IMPORTANT: Protect pipes against
7.2 A
freezing with appropriate insulation.
If the toilet is installed in an
110° F
unheated location during freezing
periods protect it as follows:
I
Shut off the water supply,
•
IP44
Activate one cycle without water,
•
67 lbs
Pour antifreeze in the bowl (2
•
0.5 HP
liters),
•
t o
t h e
a b o v e
IMPORTANT: Any bends in the
discharge pipe run should be
smooth radius bends. If using
plastic pipe, if a sweeping 90 is not
available, use two 45 degree turns
to create a smooth bend.
When connecting the discharge
pipe, it is recommended to install
a ball valve for servicing purposes
on the lowest point of the vertical
discharge. The connection to the
soil-stack should be made with
an approved TY fitting and should
be in accordance with your local
plumbing code.
Note: The connection should always
be done going into the top of the
soil stack to prevent any back
pressure into the discharge line
from the unit.
V.3
To
Sanicompact® 4C, the sink hose
(provided) would have to be
installed. Lay the Sanicompact® 4C
on its side and cut the nipple which
is situated on the motor cover that
can be seen through the back of the
unit. Connect the flexible sink hose
in the
A
and secure it to the motor cover
using a clamp. A 1-1/4" drain pipe
coming from the sink will connect to
the other end of the sink hose which
and
A
should also be secured by means
of a clamp. Note that if the sink is
B
installed on the left hand side of the
to the end
A
bowl (while facing the front of the
.
B
toilet), it will be required to have
additional back room to create a
.
loop into the sink hose connection.
C
As the discharge line interferes with
the sink hose connection, this will
only be required when the sink is
installed to the left of the bowl.
V.4
For the best possible flushing
action, the Sanicompact® 4C needs
to be connected to a 1/2-inch water
supply. The Sanicompact® 4C is
supplied with a supply hose. T
Note that the water supply hose
provided comes with a 3/8"
8
Flush the toilet.
INSTALLATION OF A SINK
(see fig. 3 and 4)
d r a i n
a
s i n k
WATER SUPPLY CONNECTION
i n t o
t h e
Publicidad
