Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Welcome and thank you for purchasing this InSinkErator instant hot
water system.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
For your satisfaction and safety, read all instructions,
!
cautions and warnings before installing or using this
dispenser.
This unit is not intended for commercial/industrial use.
SYSTEM REQUIREMENTS (HOT WATER TANK, DISPENSER
FAUCET AND OPTIONAL FILTRATION SYSTEM):
• Make sure that all electrical, plumbing and connections conform
to local codes.
• A standard, earthed (grounded), ground fault circuit interrupter
(GFCI) electrical outlet is required under the sink for the instant
hot water dispenser's electrical power. The wall outlet powering
your hot water tank must have power supplied to it continuously.
• Do not install faucet backwards. Ensure red and blue indicators
are forward-facing. Make sure handles activate forward, towards
user.
• This GFCI outlet must be fused and should not be controlled by
the same wall switch that operates the disposer unless you have a
SinkTop Switch
™
from InSinkErator
is 15 amp for 120 volt and 10 amp for 230 or 220-240 volt.
• Attach filtration system to cold water supply only. The maximum
operating water temperature of this system is 100°F (38°C).
Do not install the filter on hot water supply lines. (Filter sold
separately).
• It is recommended that a dedicated control valve be installed on
the cold water line supplying water to this system.
• To prevent damage or unit not operating properly, the water
pressure must be between 15 psi - 80 psi (1 bar – 5.5 bar; 103 kPa
–552 kPa). Ambient (room) temperature between 40°F (4°C) and
110°F (43°C).
• Do not install if water pressure exceeds 80 psi (860 kPa).
• The use of a water filter should NOT result in the water pressure
dropping below 15 psi (210 kPa).
• Do not install where water hammer conditions occur. If water
hammer conditions exist you must install a water hammer
arrester.
• The flexible vent and outlet tubes must be correctly connected
to the dispenser supplied by the manufacturer. They must not be
obstructed or connected to a normal type dispenser or any other
type.
• To protect from freezing, shut off water supply, remove filter
cartridge, drain hot water tank and tubing when temperatures are
expected to drop below 40° F (4° C).
• Do not use a torch or other high temperature sources near
system, cartridges, plastic fittings or plastic plumbing.
• Do not install near water pipes which will be in path of a drilling
tool when selecting the position to mount the components.
• Mount system in such a position as to prevent it from being struck
by other items used in the area of installation.
• Ensure that the location and fasteners will support the weight of
the system when installed and full of water.
• When mounting tank and filter, screws provided are for use in
wood studs or cabinets only. Use wall anchors (not supplied) for
installation into plasterboard.
• Ensure all tubing and fittings are secure and free of leaks.
• Filtration system intended for use with plastic water lines (such
as PEX tubing, PE Tubing, PP Tubing). Do not install using rigid
piping. (Filtration system sold separately).
• For systems using two handle HC model dispensers, operate only
one handle at a time.
• Important: Do not allow unit to continuously boil.
• Regularly inspect the system. If there are signs of water leakage,
turn off the water supply and contact InSinkErator.
®
. Fuse/circuit breaker required
• A drain pan, plumbed to an appropriate drain or outfitted with
a leak detector, should be used in those applications where any
leakage could cause property damage.
• If you suspect elevated levels of chlorine in your water, or your
water has a rusty appearance before the installation of this unit,
use of InSinkErator's water filtration system is recommended.
• This product contains stainless steel. The manufacturer cannot
guarantee against rusty water because of the number of factors
that are involved beyond the manufacturer's control. However, the
sudden appearance of rusty water discharged from the hot water
dispenser may indicate the need for service or replacement of this
product.
• Moving parts inside the tank causing a rattling noise are normal.
• For questions or concerns, please contact InSinkErator (see back
page for contact information).
ADDITIONAL CONSIDERATION WHEN UTILIZING
INSINKERATOR'S FILTRATION SYSTEM:
• The disposable filter cartridge MUST be replaced every 6 months,
at the rated capacity or sooner if a noticeable reduction in flow
rate occurs.
• Failure to replace the disposable filter cartridge at recommended
intervals may lead to reduced filter performance and cracks in the
filter housing, causing water leakage or flooding.
• After the recommended usage life, the filter should be disposed of
per applicable rules and regulations.
• Do not install filtration system if any of the quick connect collets
are missing from the filter head or Y-Quick Connector. Connect
InSinkErator if collets are missing from any fittings.
• To protect from freezing, remove filter cartridge when
temperatures are expected to drop below 40° F (4° C).
• Do not install systems in areas where ambient temperatures may
go above 110° F (43° C).
• Do not install in direct sunlight or outdoors.
• Use this hot water tank and dispenser system only for its intended
use as described in the manual.
IMPORTANT SAFETY INFORMATION
Save these instructions.
NOTICE
• This system can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the system in a safe
way and understand the hazards involved. Children shall not play
with the system. Cleaning and user maintenance shall not be
made by children without supervision.
• Do not operate this product if it has been or appears to be
damaged in any manner or after the product malfunctions or
is dropped. Return the complete product immediately to your
retailer or dealer for inspection.
• If the tank supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
A potentially hazardous situation,
which, if not avoided, could result in
death or serious injury.
A potentially hazardous situation,
which, if not avoided, may result in
minor or moderate injury.
Notice is used to address practices
not related to personal injury.
1
Publicidad
