General Safety Precautions; Machinery Directive - DITEC NRG90TXE Manual Tecnico

1. GENERAL SAFETY PRECAUTIONS

General tips and safety measures to be taken. The following tips are general rules for the use of Ditec
NGR gearmotors in combination with other equipments. You should definitely take note of these tips
during installation and use.
- The installation, the opening of the limit switch box and the Ditec NGR electrical connection must be done
without electrical tension.
- Ditec NGR must be installed with its protections and security installations. You also have to pay ATTENTION
to fix it in the correct way.
- Check before activating that the voltage for Ditec NGR is the same as the supply voltage on the site.
- The device "EMERGENCY STOP" must remain active on all modes of operation of the Ditec NGR. In case the
"EMERGENCY STOP" unlocks, it must not under any circumstances cause an undesired activation of the
Ditec NGR.
- For spare parts, see the spares price list.
- For repairs or replacements of products only original spare parts must be used.
- The installer shall provide all information relating to automatic, manual and emergency operation of the
motorised door or gate, and provide the user with operating instructions.
- The installer must prepare the maintenance log, which will indicate all the interventions of ordinary and ex-
traordinary maintenance carried out.
IMPORTANT SAFETY REGULATIONS to be respected:
- Ditec NGR must be installed in compliance with all the electrical system and safety regulations in force.
- A regular magnetothermal switch must be installed up line from the power supply circuit (16A multiple-pole
device, minimum opening contacts = at least 3mm). The switch must be opened every time the gearmotor
and its control unit are accessed.
- The connection to the power mains must be performed by qualified technicians able to work in compliance
with the regulations.
- Check that the mains voltage supplied to the system corresponds to the voltage that Ditec NGR requires. Also
check that the line has an adequate cross section and is equipped with a ground wire.
If the above mentioned requirements are not respected, Ditec declines any responsibilities while
the user is responsible for a negligent use of the product.
The packaging components (cardboard, plastic, etc.) should be disposed through the separate collection for recycling. Befo-
re proceeding however, check the local regulations regarding disposal. The packaging materials should not be discarded in
the environment or left within reach of children, as they are a potential source of danger.
2. DECLARATION OF INCORPORATION OF PARTLY COMPLETED
MACHINERY
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in Lodjursgatan 10, SE-261 44 Landskrona, Sweden, declares that the
automation system for Ditec NRG sectional doors:
- is designed to be installed on a sectional doors to form a machine pursuant to Directive 2006/42/EC. The manufacturer of the mo-
torised sectional doors must declare conformity with Directive 2006/42/EC (annex II-A) prior to initial machine start-up;
- complies with the applicable essential safety requirements indicated in Annex I, Chapter 1 of the Directive 2006/42/EC;
- complies with the Electromagnetic Compatibility Directive 2014/30/EU;
- complies with the RED Directive 2014/53/EU;
- the technical documentation complies with Annex VII-B of the Directive 2006/42/EC;
- the technical documentation is managed by the Technical Office of Entrematic Italy (with headquarters in Largo U. Boccioni 1 – 21040
Origgio (VA) – ITALY) and is available upon request, sending an e-mail to ditec@entrematic.com ;
- a copy of the technical documentation will be given to competent national authorities, following a suitably justified request.
Landskrona, 28-01-2020

2.1 MACHINERY DIRECTIVE

Pursuant to the Machinery Directive (2006/42/EC), the installer who motorises a door or gate has the same obligations as the ma-
nufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the documents indicated in Annex V of the Machinery Directive;
- (the technical data sheet must be kept and placed at the disposal of competent national authorities for at least ten years from the
date of manufacture of the motorised door or gate);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Directive and deliver it to the customer;
- affix the EC marking on the motorised door or gate, in accordance with point 1.7.3 of Annex I of the Machinery Directive.
Matteo Fino
(C (C (C ( C (C ( (C (C (C ( ( C (C (C (Chairman) (C (C (C (C ( ( C (C (C (C (C C C C C C C C C C C C ha ha h h a ha ha ha ha ha h a ha h ha ha ha ha ha hairma ha ha a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
9
n n n n n n n n n n n n)
EN