Gardena THS 500/48 Libro De Instrucciones página 10

To connect the hedge trimmer [ Fig. O1 ]:
DANGER! Electric shock!
To avoid damage to the mains cable
cable 7 must be inserted into the cable lock
v Before you operate the unit insert the extension cable
the cable lock 8 .
v Never take hold of the protective cover
unit.
1. Loop the extension cable
and pull tight.
2. Connect the plug r of the unit into the socket
cable.
3. Connect the extension cable
Work positions:
The unit can be operated in 4 positions (illustration similar).
– [ Fig. O2 ]: Side trimming: Telescopic pipe retracted
– [ Fig. O3 ]: Vertical trimming at high level: Telescopic tube
extended
– [ Fig. O4 ]: Horizontal trimming at high level: Motor unit tilted
by 75°, telescopic pipe extended
– [ Fig. O5 ]: Trimming at low level: Motor unit tilted by – 60°,
telescopic pipe extended
To start the hedge trimmer [ Fig. A1 / O6 ]:
DANGER! Risk of injury!
Risk of injury if the unit does not stop when you release
the start button.
v Do not bypass the safety devices or switches. For example
do not attach the starting lock-out
handle.
To start:
The unit is fitted with a starting lock-out
turned on by accident.
1. Remove the protective cover
2. Hold the telescopic pipe of the unit with one hand and the handle
with the other hand.
3. Push the starting lock-out
The unit will start.
4. Release the starting lock-out
To stop:
1. Release the start button e
2. Slide the protective cover
To tilt the motor unit [ Fig. O7 ]:
For cutting at high and low level, the motor unit
angle of 75° to – 60° in 15° increments.
1. Keep the orange button 9
4
2. Tilt the motor unit in the required direction.
3. Release the orange button
To extend the telescopic pipe [ Fig. O8 ]:
For cutting at high and low heights, the telescopic pipe
continuously extended by up to 45 cm.
1. Loosen the orange nut 0 .
2. Extend the telescopic pipe
0
3. Tighten the orange nut
4. MAINTENANCE
[ Fig. A1 ]:
DANGER! Risk of injury!
Cut injury when the unit starts accidentally.
v Before you maintain the unit, make sure that the mains cable
is disconnected and the protective cover
blade 2 .
10
8883-20.960.05.indd 10 8883-20.960.05.indd 10
6 the extension
8 .
7
1 when connecting the
7 , insert the loop into the cable lock
t of the extension
7
into a 230 V mains socket.
q or start button e
q
to prevent the unit from being
1 from the blade 2 .
q forwards and push the start button
q
.
.
1 over the blade 2 .
4 can be tilted at an
pressed.
9 and allow the motor unit 4 to engage.
3
can be
3 to the required length.
again.
1
is slid over the
To clean the hedge trimmer:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
into (in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
8
1. Clean the unit with a damp cloth.
2. Clean the airflow slots with a soft brush (do not use a screwdriver).
3. Lubricate the blade
Art. 2366). Avoid contact with the plastic parts.
5. STORAGE
To put into storage [ Fig. A1 ]:
The product must be stored away from children.
1. Disconnect the mains cable.
2. Clean the unit (see 4. MAINTENANCE) and slide the protective cover
2
over the blade .
3. Stow the unit in a dry area where it has protection from frost.
6. TROUBLESHOOTING
DANGER! Risk of injury!
to the Cut injury when the unit starts accidentally.
v Before you troubleshoot the unit, make sure that the mains
cable is disconnected and the protective cover
is slid over the blade
Problem
Unit does not start
w
e .
Unit can no longer
be stopped
Hedge is not cleanly cut
NOTE: For any other malfunctions please contact the GARDENA service depart-
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.
7. TECHNICAL DATA
Telescopic Hedge Trimmer
Motor power consumption
Mains voltage /
Mains frequency
Strokes
Length of blade
Tooth gap of blade
Range of extension of
telescopic tube
Weight (approx.)
Sound pressure level L
1)
pA
Uncertainty k
pA
Sound power level L :
2)
WA
measured/guaranteed
Uncertainty k
WA
Hand/arm vibration a
1)
vhw
Measuring process complying with:
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
2 with a low viscosity oil (e. g. GARDENA spray-oil
1
2 [ Fig. A1 ].
Possible Cause Remedy
Extension cable not connected v Connect the extension cable
or damaged.
or if necessary replace it.
Blade blocked. v Remove obstacle.
Start button is stuck. v Disconnect the mains cable
and loosen start button.
Blade blunt or damaged. v Have blade replaced by
GARDENA Service.
Unit Value (Art. 8883)
W 500
V / Hz 230 / 50
/ min. 1,600
cm 48
mm 25
cm 0 – 45
kg 4.1
83
dB (A)
3.0
96 / 98
dB (A)
2.3
m/s 3.8 ± 1.5
2
EN 62841-4-2 RL 2000/14/EG
1) 2)
1
31.07.23 12:18 31.07.23 12:18