EINHELL Expert TE-TS 1825/1 U Manual De Instrucciones página 35

Anleitung_TE_TS_1825_U_SPK8_- 26.09.12 15:19 Seite 35
The distance between the blade (4) and the
n
splitter (5) should be 3-8 mm.
Retighten the screw (20) and mount the table
n
insert (6) (Fig. 7).
7.5 Changing the table insert (Figure 7)
To prevent increased likelihood of injury the
n
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
n
Remove the 2 countersunk head screws (34).
n
Take out the worn table insert (6).
n
To fit the replacement table insert, proceed in
n
reverse order.
7.6 Fitting/replacing the blade (Fig. 5)
Important! Pull out the power plug first.
n
Remove the table insert by undoing the two
n
countersunk head screws (see 7.5).
Undo the nut with a size 24 wrench on the nut
n
itself and a second fork wrench (size 13) on the
motor shaft to apply counter-pressure.
Important! Turn the nut in the direction of
n
rotation of the saw blade.
Take off the outer flange and pull the old saw
n
blade off the inner flange by dropping the blade
at an angle.
Clean the blade flange thoroughly before fitting
n
the new blade.
Mount and fasten the new saw blade in reverse
n
order.
Important! Note the running direction. The
n
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the splitter (5) and the saw guard
n
(2) (see 7.3., 7.4.)
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.
8.0. Using the saw
8.1. ON/OFF switch (Fig. 4)
To turn the saw on, press the green button "I" .
n
Wait for the blade to reach its maximum speed
of rotation before commencing with the cut.
To turn the machine off again, press the red
n
button "0".
8.2. Cutting depth (Fig. 4)
Turn the hand crank (8) to set the blade (4) to
n
the required cutting depth.
Turn anti-clockwise:
Turn clockwise:
8.3. Parallel stop
8.3.1. Stop height
The parallel stop (7) supplied with the bench-
n
type circular saw has two different guide faces.
For thick material you must use the stop rail (25)
n
as shown in Fig. 12, for thin material you must
use the stop rail as shown in Fig.11.
To change over the stop rail (25) to the lower
n
guide face you have to slacken the two knurled
screws (26) in order to disconnect the stop rail
(25) from the holder (24).
Remove the two knurled screws (26) through the
n
one slot (27) in the stop rail (25) and insert in the
other slot (31).
Remount the stop rail (25) on the holder (24).
n
The procedure for changing over to the high
n
guide face is similar.
8.3.2. Cutting width:
The parallel stop (7) has to be used when
n
making longitudinal cuts in wooden workpieces.
The parallel stop (7) can be mounted on either
n
side of the saw table (1).
The parallel stop (7) has to be mounted in the
n
guide rail (22) of the saw table (1).
The parallel stop (7) can be set to the required
n
dimension with the help of the scale (23) on the
guide rail (1).
You can clamp the parallel stop in the required
n
position by pressing the eccentric lever (12).
8.3.3. Setting the stop length (Fig. 10)
The stop rail (25) can be moved in longitudinal
n
direction in order to prevent the workpiece from
becoming jammed.
Rule of thumb: The rear end of the stop comes
n
up against an imaginary line that begins roughly
at the center of the blade and runs at an angle of
45° to the rear.
Set the required cutting width
n
- Slacken the knurled screws (26) and push the
stop rail (25) forward until it touches the
imaginary 45° line.
- Retighten the knurled screws (26).
8.4. Cross stop (Figure 9)
Slide the cross stop (14) into the groove (49) of
n
the table.
Slacken the knurled screw (32).
n
Turn the cross stop (14) until the arrow points to
n
the angle required.
GB
larger cutting depth
smaller cutting depth
35