Indesit UFAN 300 Serie Manual De Instrucciones página 20

Installation
GB
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on the
bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised
technician to replace it ( see Assistance ). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these safety The manufacturer declines any liability should these safety The manufacturer declines any liability should these safety The manufacturer declines any liability should these safety The manufacturer declines any liability should these safety
measures not be observed. measures not be observed. measures not be observed.
measures not be observed. measures not be observed.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions ( see Installation ).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
1. Insert the plug into the socket and ensure that the red ALARM
and green POWER indicator lights illuminate (the
TEMPERATURE ADJUSTMENT knob must not be on
20
2. Turn the TEMPERATURE ADJUSTMENT knob to the "Super"
position: the yellow SUPER FREEZE indicator light will
illuminate.
3. When the red indicator light switches off, turn the
TEMPERATURE ADJUSTMENT knob to a medium position.
The freezer is now ready to be used.
Using the freezer to its full potential
• Use the FREEZER OPERATION knob to adjust the
temperature (see Description).
• Do not re-freeze food that is defrosting or that has already
been defrosted. These foods must be cooked and eaten
(within 24 hours).
• Fresh food that needs to be frozen must not come into contact
with food that has already been defrosted. Fresh food must be
stored in the top FREEZER and STORAGE compartment
where the temperature drops below -18°C and guarantees
rapid freezing.
• Do not place glass bottles which contain liquids, and which
are corked or hermetically sealed in the freezer because they
could break.
• The maximum quantity of food that may be frozen each day is
indicated on the data plate, which is located inside the freezer
(for example: 4 kg per 24 hours).
• In order to obtain a greater amount of space in the freezer
compartment, you may remove the bins (except the lowest
bin) and place the food directly onto the evaporator plates.
• To freeze food (if the freezer is already in operation):
- For small quantities measuring less than half of the value
indicated on the data plate, turn the TEMPERATURE
ADJUSTMENT knob to the SUPER (rapid freezing) position
(the corresponding yellow indicator light will illuminate), place
the food inside and close the door. After 24 hours, once the
freezing process is complete, turn the knob back to its normal
operating position.
- For large quantities measuring over half of the maximum
value indicated on the data plate, turn the TEMPERATURE
ADJUSTMENT knob to the SUPER position 24 hours before
placing the food you wish to freeze inside. After another 24
hours, once the freezing process is complete, turn the knob
back to its normal operating position.
! Do not open the door during freezing.
! If there is a power cut or malfunction, do not open the freezer
door. This will help maintain the temperature inside the freezer,
ensuring that foods are conserved for at least 9 -14 hours.
! Warning Indicator Light. When this red warning light comes on
for a prolonged period of time, it means that the freezer is not
functioning properly and the temperature is rising too much. (Call
your Service Centre).
This warning light might come on for a brief period when:
a) the door is left open for an extended period of time (when the
freezer is being loaded or unloaded).
b) the TEMPERATURE ADJUSTMENT knob is turned to the
"Super" setting.
In these two cases, the fact that the warning light comes on does
not indicate that the freezer is malfunctioning or there is a defect.
ice tray
Ice 3
The fact that they are situated on the top part of the freezer
drawers ensures greater cleanliness: the ice no longer comes
into contact with the food placed inside the freezer compartment;
furthermore, the dripping of the water during filling is avoided (a
lid to cover up the hole after filling with water is also provided).
1. Pull out the tray by pushing it up. Check that the tray is ompletely
empty and fill it with water through the opening provided.
2. Take care not to exceed the level indicated (MAX WATER
LEVEL). Excess water prevents the ice cubes from dispensing
).
(if this happens, wait for the ice to melt and empty the tray).