Descargar Imprimir esta página

WORXNITRO WG325 Manual Del Usuario página 18

Publicidad

Idiomas disponibles

Idiomas disponibles

4. INTENDED USE
• The pruning saw is intended for cutting only wood
and branches up to a diameter corresponding to the
length of the pruning saw guide bar.
• The pruning saw must be used at ground level or
from a suitable platform that is completely stable
and secure.
• The pruning saw is intended for outdoor use only.
• The pruning saw is not intended for any other use.
• Mounting of parts on the pruning saw is authorized
only for original or manufacturer-approved spare
parts (chain guides or saw chains for example)
EW [IPP EW JSV EYXLSVM^IH GLEMR KYMHI  WE[ GLEMR
combinations as indicated in the manual.
• The user is responsible for any accident resulting
JVSQ MQTVSTIV YWI SV YREYXLSVM^IH QSHM GEXMSR SJ
the pruning saw.
5. ASSEMBLY
WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
MOUNTING THE SAW CHAIN
1. Unpack all parts carefully. Remove the Housing-
Cover by turning the Housing-Cover Knob in a
counterclockwise direction. (See Fig. A1)
2. Place the pruning saw on a solid, level surface.
3. Use only genuine Worx Chains or those
recommended for Guide Bar.
18
4. Slide the Chain in the slot around the Guide Bar.
Ensure the Chain is in correct running direction
by comparing it to the chain icon on the Guide
Bar, or referring to the chain direction symbol
found on the saw body. (See Fig. A2)
5. Fit the Chain onto the Drive Sprocket, so that the
Fastening Bar Bolt and the Bar Locating Tab on
XLI &EV 4EH X MRXS XLI OI][E] SJ XLI STIRMRK SR
the Guide Bar. (See Fig. B1, B2)
6. Assure all parts are seated properly. Make
sure the drive links are fully seated in the Drive
Sprocket (See Fig. C1), avoiding a kink as shown
in Fig. C2. If kink occurs, pick up the Chain at the
+YMHI &EV NYWX ELIEH SJ XLI OMRO ERH XLIR TYPP XLI
kink out.
NOTE: Chain should rotate freely and be free of
kinks.
7. Fit the Housing Cover. Tilt the guide bar forward
where the guide bar tip is pushed in an vertically
downward direction. This will remove slack from
the chain. The correct chain tension is reached
when the chain can be raised approx. Half the
drivelink depth from the guide bar in the center.
This should be done by using one hand to raise
the chain against the weight of the machine.
Then tighten the Housing Cover by turning the
Housing-Cover Knob clockwise until it is tight.
Cordless Pruning Saw
(See Fig. D)
NOTE: The chain is properly tensioned when
it can be lifted off of the Guide Bar and the
drivelink is within the rail of the Guide Bar. (See
Fig. E)
NOTE: The chain will stretch while cutting and
lose proper tension. When the chain becomes
loose, completely unscrew the Housing-Cover
Knob or turn the knob around three full turns in a
counter-clockwise direction, then retighten the
Housing-Cover Knob to properly reset the chain
tension by repeating Steps 1-7 listed above.
NOTE: New saw chains will stretch. Check the
GLEMR XIRWMSR JVIUYIRXP] [LIR VWX YWIH ERH
tighten when the Chain becomes loose around
the Guide Bar.
ASSEMBLING THE EXTENSION POLE
Align and insert the handle of extension pole into
the shaft. Rotate the Locking Collar clockwise to
lock. (See Fig. F1, F2)
NOTE: 1EOI WYVI XLEX XLI WLEJX MW VQP] PSGOIH MR
place.
ASSEMBLING THE EXTENSION POLE TO THE
MACHINE (See Fig F3, F4)
Step 1: Align and insert the extension pole into the
saw.
Step 2: Hang the buckle on the hook of the saw.
Press the Clamping Lever to tighten the extension
pole to the machine.
NOTE: Make sure the extension pole is locked into
position securely before operation.
REMOVING THE EXTENSION POLE (See Fig. F5)
Loosen the Clamping Lever to release the buckle.
Press the Extension Pole Release Button to
disconnect the extension pole with the saw.
WARNING! When using this machine with the
Extension Pole, make sure that the battery pack
has been removed.
LUBRICATION (See Fig.G1, G2)
-QTSVXERX 8LI 4VYRMRK 7E[ MW RSX PPIH [MXL SMP
-X MW IWWIRXMEP XS PP [MXL SMP FIJSVI YWI 2IZIV
operate the Pruning Saw without chain oil or at an
empty oil tank level, as this will result in extensive
damage to the product.
NOTE: Chain life and cutting capacity depend on
optimum lubrication. Therefore, the chain should
be oiled before operation.
Filling oil tank (See Fig.G1):
WARNING: Removing the battery pack before
PPMRK XLI SMP XERO
1. Set Pruning Saw on any suitable surface with oil
PPIV GET JEGMRK YT[EVH
 'PIER EVIE EVSYRH XLI SMP PPIV GET [MXL GPSXL ERH
EN

Publicidad

loading

Productos relacionados para WORXNITRO WG325

Este manual también es adecuado para:

Wg325.x