Publicidad
Idiomas disponibles
Idiomas disponibles
contact hidden wiring. Saw chains contacting a
"live" wire may make exposed metal parts of the
pruning saw "live" and could give the operator
an electric shock.
c) Wear safety glasses protection. Further
protective equipment for hearing, head, hands,
legs and feet is recommended. Adequate
TVSXIGXMZI GPSXLMRK [MPP VIHYGI TIVWSREP MRNYV] F]
]MRK HIFVMW SV EGGMHIRXEP GSRXEGX [MXL XLI WE[
chain.
d) Do not operate a pruning saw, on a ladder, from
a rooftop, or any unstable support. Operation
of a pruning saw in this manner could result in
WIVMSYW TIVWSREP MRNYV]
e) Always keep proper footing and operate the
TVYRMRK WE[ SRP] [LIR WXERHMRK SR \IH
secure and level surface. Slippery or unstable
surfaces may cause a loss of balance or control
of the pruning saw.
f) When cutting a limb that is under tension ,
be alert for spring back. When the tension in
XLI [SSH FVIW MW VIPIEWIH XLI WTVMRK PSEHIH
PMQF QE] WXVMOI XLI STIVEXSV ERHSV XLVS[ XLI
pruning saw out of control.
g) Use extreme caution when cutting brush and
saplings. The slender material may catch the
saw chain and be whipped toward you or pull
you off balance.
h) Carry the pruning saw by the front handle with
the pruning saw switched off and away from
your body. When transporting or storing the
TVYRMRK WE[ EP[E]W X XLI KYMHI FEV GSZIV
Proper handling of the pruning saw will reduce
the likelihood of accidental contact with the
moving saw chain.
i) Follow instructions for lubricating, chain
tensioning and changing the bar and chain.
Improperly tensioned or lubricated chain
may either break or increase the chance for
kickback.
j) Cut wood only. Do not use pruning saw for
purposes not intended. For example: do not
use pruning saw for cutting metal, plastic,
masonry or non-wood building materials. Use
of the pruning saw for operations different than
intended could result in a hazardous situation.
k) This pruning saw is not intended for tree
felling. Use of the pruning saw for operations
different than intended could result in serious
MRNYV] XS XLI STIVEXSV SV F]WXERHIVW
l) Do not operate a pruning saw in a tree unless
]SY LEZI FIIR WTIGM GEPP] XVEMRIH XS HS WS
Operation of a pruning saw in a tree without
proper training could increase the risk of
serious personal injury.
m) Follow all instructions when clearing jammed
material, storing or servicing the pruning saw.
Make sure the switch is off and the battery
pack is removed. Unexpected actuation of the
Cordless Pruning Saw
TVYRMRK WE[ [LMPI GPIEVMRK NEQQIH QEXIVMEP SV
WIVZMGMRK QE] VIWYPX MR WIVMSYW TIVWSREP MRNYV]
R
6IGSQQIRHEXMSR XLEX XLI VWXXMQI YWIV
should, as a minimum, practise cutting logs on
a saw-horse or cradle.
0) Recommendation to have sharpening and
maintenance of the saw chain performed by
authorised service centres.
2) Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the
KYMHI FEV XSYGLIW ER SFNIGX SV [LIR XLI [SSH
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and back
towards the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the operator.
Either of these reactions may cause you to lose
control of the saw which could result in serious
TIVWSREP MRNYV] (S RSX VIP] I\GPYWMZIP] YTSR XLI
safety devices built into your saw. As a pruning saw
user, you should take several steps to keep your
GYXXMRK NSFW JVII JVSQ EGGMHIRX SV MRNYV]
/MGOFEGO MW XLI VIWYPX SJ TVYRMRK WE[ QMWYWI ERH
or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as
given below:
E
1EMRXEMR E VQ KVMT [MXL XLYQFW ERH RKIVW
encircling the pruning saw handles, and
position your body and arm to allow you to
resist kickback forces. Kickback forces can be
controlled by the operator, if proper precautions
are taken. Do not let go of the pruning saw.
b) Do not overreach and do not cut above
shoulder height. This helps prevent unintended
tip contact and enables better control of the
pruning saw in unexpected situations.
c) Only use replacement bars and chains
WTIGM IH F] XLI QERYJEGXYVIV Incorrect
replacement guide bars and saw chains may
GEYWI GLEMR FVIEOEKI ERHSV OMGOFEGO
d) Follow the manufacturer's sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
FOR PRUNING SAW WITH
THE EXTENDED POLE
SAFETY WARNINGS
Important Safety Instructions
WARNING: Read all safety warnings and
instructions. Failure to follow the
warnings and instructions may result in
IPIGXVMG WLSGO VI ERHSV WIVMSYW MRNYV]
5
EN
Publicidad
