Publicidad
Idiomas disponibles
Idiomas disponibles
Error message/
Response of Magnet Button
Indicator flashes red once
or several times
Indicator lights up red for 1
s and then goes out
Indicator does not light up
Charge-control Indicator on the Battery
(see page 16).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
The charge condition can only be read when the battery
is removed.
When the battery is mounted and the magnet is already
activated, set the magnet lever back to 30% or, if
required, back to 0% and then again to 100%. Press the
charge-control indicator button
the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Transport.
The Li-ion batteries are subject to the Dangerous
Goods Legislation requirements. The user can trans-
port the batteries by road without further require-
ments.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
Renew stickers and warning indications on the power
tool when aged and worn.
Meaning
Motion sensor has actuated
Overload shut-off has actuated
Buttons anticlockwise rotation/
clockwise rotation/STOP blocked
Battery charge too low
Power tool is defective
The machine is in sleep function
Battery dead or defective
Power tool is defective
or
to indicate
Corrective Action
After malfunction correction, the power
tool can be switched on again.
Check charge condition of battery
Send the machine to your FEIN customer
service agent.
Set magnet lever back to 30% or, if
required, back to 0% and then again to
100% (sleep function is deactivated).
Check charge condition of battery
Send the machine to your FEIN customer
service agent.
After several hours of operation, the play in the dove-
tail guide can increase. As a consequence, the drill
motor can glide alongside the dove-tail guide by itself.
In this case, retighten all set screws of the dove-tail
guide correspondingly so that the drilling motor can
easily be moved manually, yet does not glide by itself
(see page 19).
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
For FEIN power tools and accessories in need of repair,
please contact your FEIN after-sales service. The
address can be found on the Internet under
www.fein.com.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts your-
self:
Application tools, hand pump, battery
Maintenance and cleaning.
Occasionally clean the ventilation slots and the battery
terminals with a soft, clean and dry brush.
– Do not use chemical substances for cleaning the bat-
tery.
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
en
37
Publicidad
