Publicidad
Idiomas disponibles
Idiomas disponibles
USING A STRAIGHT
EDGE (Fig. 15)
l
_ WARNING:
ALWAYS clamp and support
workpiece
securely. ALWAYS
maintain
proper control of saw. Failure to damp and support workpiece combined
with loss of control of saw could result in serious injury.
1. You can make an efficient rip guide
by clamping a straight edge to your
Fig. 15
workpiece.
HOWTO
SETYOUR
BEVEL
ANGLE
(Fig. 17)
1. Remove the battery pack from saw.
Z_ WARNING:
Failure to remove
battery pack from saw could result in
accidental
starting
causing
possible
serious personal
injury.
Fig.
1'7
Bevel Adjustment
Lever
2. Carefully guide the saw along the
straight edge for a straight rip cut
(see Fig. 15).
3. ALWAYS
LETTHE BLADE REACH
FULL SPEED, then carefully
guide
the saw into the workpiece. DO NOT
bind the blade in the cut. Push the
saw forward at a speed where the
blade is not laboring.
iNSTALLiNG
AND USING
EDGE GUIDE
(sold separately)
(Fig. 16)
1. Remove the battery pack from saw.
/_
WARNING:
Failure to remove battery pack from saw could result in
accidental
starting
causing
possible serious
personal injury.
2. Place the Lock=Off Switch into the center position to lock the power off.
3. Position the edge guide so the arm with the inch increments is facing "up". Slide the arm of
the edge guide into the mounting slots at the front of the saw's base (see Fig. 15).
4. Adjust the edge guide to the desired
length of cut.
5. Tighten the edge guide retaining screw.
6. Clamp and support the workpiece
securely before making your cut.
7. Place the edge guide firmly against
the edge of the workpiece
(see Fig. 16). Doing this will give you
a true cut without pinching the blade.
8. BE SURE that the guiding edge of the
workpiece is straight so you can get a
straight cut.
9. ALWAYS LETTHE BLADE REACH
FULL SPEED, then carefully guide
Rip/Edge
Guide
Fig. 16
i
Rip/Edge Guide
Through Slots
the saw into the workpiece. DO NOT bind the blade in the cut. Push the saw forward at a
speed where the blade is not laboring.
[
/
24
2. Place the Lock=Off Switch into the center position to lock the power off.
3. Loosen bevel adjustment lever (see Fig.17).
4. Raise the motor housing end of the saw until the bevel pointer reaches the desired angle setting
on the bevel scale.
5. Tighten the adjustment lever securely.
MAKING BEVEL CUTS (Figs. 18)
m
Line of Cut=',
Fig. 18
m
450 Indicator_
0 4s
2
z_
WARNING:
ALWAYS clamp and support workpiece securely. ALWAYS maintain
proper control of saw. Failure to clamp and support workpiece and loss of control of
saw could result in serious injury.
1.Your saw can be adjusted to cut at any angle between 0° and 50°. When making 45 ° bevel cuts,
there is a notch in the saw base to help you line up the blade with the line of cut (see Fig. 18).
2. Align your line of cut with the left side of the notch by the 45 ° indicator when making 45 °
bevel cuts.
3. Since blade thicknesses vary and different angles require different settings, MAKE ATRIAL
CUT in scrap material along the guideline to determine how much, if any, you should offset the
blade from the guideline to allow for the kerf of the blade to get an accurate cut.
4. When making a bevel cut HOLD the saw FIRMLY with both hands (see Fig. 18).
5. Rest the front edge of the base on the workpiece, then squeeze the trigger switch to start the
saw. ALWAYS let the blade reach full speed, then guide the saw into the workpiece.
6. After completing your cut, release the trigger switch and allow the blade to come to a complete
stop in the cut. DO NOT remove the saw from the workpiece while the blade is moving. It will
damage your bevel cut and cause Kickback.
Z_ WARNING:
if the blade comes in contact with the workpiece
before it reaches
full speed, it could cause the saw to kickback towards you, possibly resulting in
serious injury.
25
I
I
I
Publicidad
