Publicidad
Idiomas disponibles
Idiomas disponibles
ELECTRICAL
SAFETY
Z_ WARNING:
BE SURE to read and understand
all instructions
before
|
operating
this saw. Failure to follow
all instructions
listed below
may result
in
J
electric shock, fire and/or
serious
personal
injury.
A battery operated
tool with integral batteries
or a separate
battery pack must be
recharged only with the specified
charging
stand/transformer
for the battery. A
charger that may be suitable
for one type of battery may create a risk of fire when
used with another battery.
1. Use battery operated saw only with specifically
designated
battery packs. Use of any
other batteries may create a risk of fire.
2. Use battery packs only with charging
stand/transformers
listed.
SAW
CHARGING STAND/TRANSFORMER
BATTERY PACK
172.67098
CDT218GU-103/BHY41-23.5V-200mA
CDT218GU-104(ABP318GU)
Can also use 1426101 and 140295004
Can also use 1323509,
1323520, 130260001,
130139020 and 130139021
3. Do not abuse the cord on the charging
stand. Never carry the charging
stand/transformer
by its power cord. Never pull the power cord to remove the transformer
from the power outlet. Damage to the cord or charging stand/transformer
could occur and
create an electric shock hazard. Keep cord away from heat, oil, sharp edges or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk of electric
shock.
SERVICE SAFETY cont.
2. Tool service must be performed only at a Sears Parts and Repair Center. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
3. When servicing
a tool, use only identical replacement
parts. Follow instructions
in the maintenance
section
of this manual.
Use of unauthorized parts or failure to
follow maintenance instructions may create a risk of electric shock or injury.
SAFETY RULES FOR CORDLESS
CIRCULAR SAWS
Keep hands away from cutting area and blade. Keep your
second hand on the auxiliary handle or motor housing. If both hands are holding
the saw, the blade cannot cut them.
CAUTION:
Blades coast after saw is switched off.
/k
1. KEEP your body positioned
to either side of the saw blade and not in direct
line with the saw blade. Kickback could cause the saw to jump backwards. (See
"Kickback...What Causes it and Ways to Prevent it"on pages 18 and 19).
2. DO NOT reach underneath the work. The guard cannot protect you from the blade
beneath the workpiece.
]
]
3. CHECK lower guard for proper closing BEFORE each use. DO NOT operate the saw
if the lower guard does not move freely and dose instantly. Never clamp or tie the
lower guard in the open position. If the saw is accidentally dropped, the lower guard may
SAFETY
SYMBOLS
FOR YOUR TOOL
The label on your tool may include
the following
symbols.
V.......................................................................Volts
A ......................................................................Amps
Hz ....................................................................Hertz
W.....................................................................Watts
....................................................................Alternating current
--.
................................................................Direct current
no ....................................................................No-load speed
[] ....................................................................Class II construction, Double Insulated
RPM ......................................................
Revolutions per minute
SPM .........................................................
Strokes per minute
OPM .........................................................
Orbits per minute
,4k....................................................................Indicates danger, warning or caution.
It means attention! Your safety is involved.
SERVICE
SAFETY
1. If any part of this cordless
saw is missing
or should
break, bend, or fail in any
be bent. Raise the lower guard with the retracting lever.The guard is operating properly
when it moves freely, does not touch the blade or any other part in all angles and depths
of cut, and readily returns to the closed position.
4. CHECK the operation and condition
of the lower guard spring. If the guard and the
spring are not operating properly, they MUST BE serviced before use. The lower
guard may operate sluggishly, due to damaged parts, gummy deposits, or a buildup of
debris. DO NOT operate your saw until the damage has been repaired or replaced.
5. The lower guard should be retracted manually ONLY for making special cuts, such
as pocket or compound
cuts. ALWAYS raise the lower guard by retracting its lever.
As soon as the blade enters the material, the lower guard MUST be released. For all
other sawing, the lower guard should operate automatically.
6. ALWAYS make sure that the lower guard is covering the blade BEFORE placing the
saw down on a work bench or floor. An unprotected moving blade will cause the saw to
walk backwards, cutting whatever is in its path. Make note of the time it takes for the blade
to stop spinning after the switch is released.
7. NEVER hold the piece being cut in your hands or across your legs. It is important to
support the workpiece properly in order to minimize body exposure, blade binding, or loss
of control.
way; or should any component
fail to perform properly: have the missing, damaged
or failed parts replaced BEFORE resuming operation.
6
I
I
I
When sawing through
a workpiece,
the lower blade guard DOES
NOT cover the blade on the underside of the workpiece (Pg. 16 Fig. 4). ALWAYS keep
J
your hands and fingers away from the cutting area.
Publicidad
