Publicidad
Idiomas disponibles
Idiomas disponibles
Refer to Figures 11 - 38.
DESCRIPTION
The Graftaman Belt and Disc Bander is constructed of rugged
die cast aluminum and cast iron providing stabilityand vibra-
tion-free operation. The belt and disc are used to sand,
deburr, bevel and grind workpieces of wood and plastic.
The belt housing can be pivoted from vertical to
hodz.ontal for sanding large, straight workpisoes. The idler
drum permits the sanding of contoured shapes and finishes•
The disc can be used to sand or bevel surfaces.
Built in dust collection system collects dust from the belt and
disc and exhausts the dust into an included 30--micron collec-
tion bag.
The adjustable miter gauge is used on the work table for guid-
ing the workplace at a desired angle while sanding. Work stop
included for sanding long pieces on the belt.
SPECIFICATIONS
Belt alze ....................................
4 x 36"
Belt platen area ...............................
5 x 9"
Bait speed ................................
1100 FPM
Disc diameter ....................................
8"
Disc speed ...............................
2200 RPM
Table dimenalons ..............................
6 x 9"
Table tilts ...................................
0 to 45°
Dust port diameter ................................
2"
Base dimensions ............................
12 x 17"
Switch .............................
SP, Locking rocker
Weight ......................................
551be
WARNING:
Operation of any power tool can result in toralgn
objects being thrown into the eyes, which can result in severe
eye damage. Always wear safety goggles complying with
United States ANSf Z87.1 (shown on package) before com-
mencing power tool operation. Safety goggtes are avaltable at
Sears retail stores or catalog.
CAUTION;
Always observe falio,Mmg safety precautions.
SAFETY
PRECAUTIONS
• Whenever adjusting or reptacing any parts on the tool, turn
switch OFF and remove the plug from power source.
• Recheck table handle and bolts.They must be tightened
securely.
• Make sure all guards are properly attached. All guards
should be securely fastened.
• Make sure all moving parts are free and clear of any
interference.
• Make sure all fasteners are tight and have not vibrated loose.
• With power disconnected, test operation by hand for clear-
ance and adjust it necessary.
• Always wear eye protection or face shield.
• Make sure abrasive belt always tracks properly. Correct
tracking gives optimum performance.
• After tumthg switch on, always allow belt and disc to come
up to full speed before sanding or grinding.
• Be sure disc turns counterclockwise. Abrasive belt must
travel downward.
* Avoid kickback by sanding in accordance with the direction-
al arrows.
• Keep your hands diear of abrasive belt, disc and all moving
part_.
• For optimum performance, do not stall motor or reduce
speed. Do not ferns the work into the abrasive.
• Always support workpiece with table or work stop when
sanding with belt and with table when sanding with disc.
• Never push a sharp comer ot the workpisoe rapidly against
the bert or disc. Abrasive backing may tear.
• Replace abrasives when they become loaded (glazed) or
frayed.
WARNING:
Some dust created by power sar_ding, sawing,
grindiog, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm•
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other mason-
P/products.
• Arsenic and chromium from chemically-trsatad
lumber.
Your risk from these exposures vary, depending on how often
you do this type of work. To reduce your'exposure to these
chemicals: work in a well ventilated area and work with
approved salety equipment. Always wear MSHA/NIOSH
approved, properly fittiog face mask or respirator when using
such tools.
ON/OFF
SWITCH
Refer to Figure 11.
The ON/OFF switch is located on the upperfront right of the
base.To turn the sander ON, puff the switch to the up
position. To turn the sander OFF, push the switch to the down
position.
The sander can be locked from unauthorized use by locking
the switch. To lock the switch:
* Turn the switch to OFF position and disconnect sander
from power source.
• PuE{ the key out, The switch cannot be turned on with the
key removed.
NOTE: Should the key be removed from the switch at the ON
position, the switch can be turned of_but cannot be turned on
again.
* To replace key, slide key into the slot on switch until it snaps.
11- Locking
Switch in OFF Position
Publicidad
