Craftsman 139.53939D Manual Del Propietário página 31

Usingthe Wall-MountedDoor Control
THE SMART CONTROLPANEL ®
Press the push button to
open or close the door.
Press again to reverse the
door during the closing
cycle or to stop the door
while it's opening.
This door control contains
a motion detector that will
automatically turn on the
light when it detects a
person entering the garage.
This feature can be easily turned
off for extended work light use.
Motion Detecting
Light On/Off
Prog <Learn> _
Hour
Minute --
i
Language J
Degrees (F/C) /
_ _/,Push Bar
\ LockButton
Light Feature
I U IPress the Light button to turn the opener light on or off.
LIGHT
I lit will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the light will
remain on for 4-1/2 minutes. Press again to turn it off sooner. The
4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until the light
blinks (about 10 seconds). A single blink indicates that the timer
is reset to 1-1/2 minutes. Repeat the procedure and the light will
blink twice, resetting the timer to 2-1/2 minutes. Repeatagain for
a 3-1/2 minute interval, etc., up to a maximum of four blinks and
4-1/2 minutes.
When using the opener lights as working lights, we recommend
that you first disable the motion sensor.
Motion Detecting Light Feature: The opener light will turn on
automatically when a person walks in front of the wall-mounted
door control. This feature works by detecting motion and body
heat and may not work in temperatures around 100° F, (37.7° C).
The opener light will come on for 5 minutes, then shut off
automatically if no additional motion or heat differential is
calculated.
To disable this feature, press the Automatic Light 0n/0ff button
on the left side of the door control.
Q e recommend that you disable the motion sensor
when using the opener lights as working lights.
Otherwise, they will turn off automatically if you are
work ng beyond the sensor s range.
LockFeature
I I I IDesignedto prevent operation of the door from
I LOCK Ihand-held remote controls. However, the door will open
and close from the door control, the Outside Keylock and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds. The
push bar light will flash as long as the Lock feature is on.
To turn off, press and hold the Lock button again for 2 seconds.
The push bar light will stop flashing. The Lock feature will also
turn off whenever the "learn" button is activated.
PROG<Learn> Feature
The door control is equipped with a PROG<LEARN>button to
assist in learning remote controls to the unit. Press the PROG
<LEARN>button once to initiate LEARN mode and the display will
show 'Learn RemoteControl - Press Learn Button Again to
Confirm.' Press the PROG<LEARN>button a second time and the
display will show 'Learn Mode - Press Remote Control Button to
Learn Remote.' Press the button of the remote control to be
learned and the worklight will blink to confirm the remote control
has been learned.
Hour and Minute Feature
H--_--M
Press or hold either of these side buttons to
increment the hour or minute displayed on the
LCD display.
<LANG>LanguageFeature
Press this side button to toggle between the three languages-
English, Spanish, and French.
DegreesF/C Feature
Press this side button to toggle the temperature units
between Fahrenhet and Ces us.
Display ContrastAdjustment
Press and hold the light button then push the hour button to
increase the contrast or the minute button to decrease the
contrast.
Additional feature when used with the 3-Function
hand-held remote
To control the opener lights:
1. With the door closed, press and hold a small
remote button that you want to control the
light.
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock button
on the door control.
4. After the opener lights flash, releaseall buttons.
31