Olymp LavaSit COMFORT Instrucciones De Montaje página 6

Mounting instructions for waterpipe installers:
Important: Read these instructions thoroughly before
installing the appliance. Determine the precise position in the
salon with the salon owner and the installation specialist.
•
The wash unit is intended for operation in clean and
dry rooms at normal room temperature.
•
In the water supply system only original components
supplied by the manufacturer must be used.
•
The house installation must be equipped with a pressure
reducing valve. Recommended water pressure for the
shampoo station: approx. 3 – 5 bar.
•
The new set of hoses supplied with the unit must be
used. Old hoses must not be used.
•
Observe minimum power socket spacing specified in
DIN VDE 0100 and VDE 0100 Part 701.
•
Observe the height of the drain and installation shaft.
1. We recommend to provide the supply lines with
a central shut-off device.
If the system is operated without a suitable shut-off
device, the angle valves must be closed at the end
of business hours.
2. Install the supply water and waste water lines as
shown in Fig. 2.
Mounting instructions for appliance fitters:
3. Prepare the shampoo unit for installation: (Fig. 1)
- Remove inspection door (5): Grasp the opening and
pull back, then lift out downwards.
- Plug in power cable.
- Extend leg rest to final position.
- Remove cover at the bottom of the chair (7)
(4 allen screws + Velcro fastening)
- Detach side panels from front section (3+4):
Release each of the 2 hexagonal socket. head screws
inside the pillar covering (1), push the covers
forward, then tilting sidewards pull off from the leg
rest pipes as shown in Fig. 3
4. Prepare the cover sections (1+2) for connection of the
installation tunnel:
- Make sure that the mounting side corresponds to
that shown in the installation diagram!
- Make a drilling Ø 80 mm and 4 drillings Ø 5.5 mm for
the connection adapter as shown in Figure 2.1
5. Align the substructure (6) according to the
installation template and secure to the floor:
6 anchor bolts M 10 x 125 (extending 30 mm
above the finished floor) or metal plugs with metric
thread for hexagonal screws M 10 x 60.
Use 6 rubber washers (6.1) between framework and
floor.
Comfort MO W+R
GB
Mounting instructions for waterpipe installers:
6. Make sure that pipes/pressure hoses are parallel.
Connect the unit. Fit 40 mm dia. waste water pipe and
R ½" pressure lines with stop taps between the wall and unit.
Prevent the stop valves from turning while they are
being screwed on. Connect the waste water hose to the
siphon using a seal and union nut. Insert the waste water
hose at least 3 to 4 cm into the siphon. Connect the drain
bushing to the waste water hose using
a hose clamp.
7. Close the mixing tap. Open the stop valve and check for
leaks with the mixing tap closed. Check the mixed water.
The hot water and cold water supply must correspond to
the coloured symbols on the mixing tap.
8. Check the pressure of the unit with 8 bar water pressure.
Then set the pressure to 3 to 5 bar. On completion of the
installation work, always rinse out the water pipes. A central
regulating tap is required if more than one unit is installed.
This tap must be easily accessible from the salon.
These mounting instructions apply to the connection of
one unit. If more than one unit is to be installed, the pipe cross
section must be increased accordingly.
Important: If the water pressure is above 5 bar, it must be
regulated by a pressure reduction valve.
Note for salon owners:
The connections described under points 1 to 2 and 6 to 8 must be
performed by the installer. The installer is responsible for any
problems that may occur. The manufacturer of the unit shall not
accept warranty claims for this work.
Mounting instructions for appliance fitters:
9.
Mount installation tunnel:
Connection to the shampoo station: (Fig. 2.1)
Mount the connection adapter (2) with connection rubber
(1) using M5 screws, washers and nuts.
Connection to the wall: (Fig. 2.2)
Mount 3 mounting brackets (4) onto the wall.
Shorten the installation tunnel if necessary, and provide it
with edge protection rubber at wall side.
Put on the installation tunnel. Insert connecting clips (5) on
the underside of the installation tunnel.
10. Only for in-line installation: (Fig. 2.1)
Mount the connection adapter (2) with connection rubber
(1) using M5 screws, washers and nuts.
Put on the installation tunnel. Insert connecting clips (5) on
the underside of the installation tunnel.