Publicidad
Idiomas disponibles
Idiomas disponibles
nism will release as shown in figure L.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position after
rotating the stall release lever, proceed to "clearing a jammed
nail".
Clearing a Jammed Nail (Fig. M,N)
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
Remove battery pack from tool and engage trigger lock-
u
off.
Remove any loaded nails. Refer to Loading and Unloading
u
the Tool.
Lift the jam clearing latch 7 then pull up to open front door
u
17 .
Remove bent nail, using pliers if necessary.
u
If driver blade is in the down position, cycle stall release
u
lever 6 using enough force to fully slide it to the other end
of the slot in housings.
Close the front door and engage the latch pin under the
u
two arms 18 on the nosepiece. Push latch until it locks in
place.
Reinsert battery pack.
u
Warning!If a jam occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
the jammed nail. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
Note!Should nails continue to jam frequently in contact trip,
have tool serviced by an authorized STANLEY service center.
Cold Weather Operation
When operating tools at temperatures below freezing:
Keep tool as warm as possible prior to use.
u
Actuate the tool 5 or 6 times into scrap lumber before
u
using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
No-mar tip (Fig. O)
The tool comes equipped with a spare no-mar tip (19) located
on the side of the nail magazine.
To replace the no-mar pad, simply pull off the old no-mar pad
and refit the new no-mar pad onto the contact trip (8).
(Original instructions)
Replacement parts
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
The tool comes equipped with a spare no mar tip located on
the side of the nail magazine.
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at www.stanleytools.com.
You can also order parts from your nearest
STANLEY Factory Service Center or STANLEY Authorized
Warranty.
Accessories
Warning! Since accessories, other than those offered by
STANLEY, have not been tested with this product, use of
such accessories with this tool could be hazardous. To reduce
the risk of injury, only STANLEY recommended accessories
should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Troubleshooting
If your appliance seems not to operate properly, follow the
following instructions.
If this does not solve the problem, please contact your local
STANLEY repair agent.
Warning! Before proceeding, unplug the appliance.
Problem
Possible Cause
Unit will not start.
Battery pack not
installed properly.
Battery pack not
charged.
Trigger lock-off is
engaged.
Tool doesn't
Motor stops running
actuate.
after 2 seconds.
(Headlights on,
motor does not
run)
Tool doesn't
Low battery charge or
actuate.
damaged battery.
(Headlights
flash)
Tool doesn't
Jammed fastener / tool
actuate.
stalled.
(Headlights flash
continuously)
Jammed mechanism
Tool doesn't
actuate.
((Headlights on,
motor runs,
driver blade
stuck down)
ENGLISH
Possible Solution
Check battery pack
installation.
Check battery pack charging
requirements.
Disengage trigger lock-off.
Normal operation; release
trigger or contact trip and
re-depress.
Charge or replace battery.
Remove the battery, rotate the
stall release lever. Clear the
jammed fastener, and reinsert
battery pack.
See authorized service center.
See authorized service center.
31
Publicidad
