YATO YT-82151 Manual Original página 16

GB
Adjust the splitting edge in accordance with the description in this manual. Incorrect setting, a wrong position or misalign-
ment may make the splitting edge useless in the context of prevention of backward recoil.
Always use a splitting, except for deep cutting. The splitting edge must be installed again after deep cutting. The splitting edge
causes disturbance during deep cutting and may cause backward recoil.
In order to function correctly, the splitting edge must be introduced into the element being processed. The splitting edge
is useless in prevention of backward recoil during short cuts.
Do not operate the sawing machine, if the splitting edge is bent. Even slight bends may slower the closing of the guard.
INSTALLATION OF THE EQUIPMENT
ATTENTION! The equipment may be installed only if the power supply if off . Remove the plug of the cable the tool from the
mains socket!
The sawing machine is supplied complete. Once the package has been opened, make sure all the elements have been supplied.
Then check the connections and if necessary tighten the bolt connecting the base to the fi xed guard and tighten the tighten bolts
fi xing the splitting edge, if the sawing machine is equipped with a wedge. Before fi rst use, install the circular saw.
PREPARATION FOR WORK
Before work may commence, make sure the body and the power supply cable with plug are not damaged. In case any damage
is detected, it is prohibited to continue work.
Attention! All activities related to installation and replacement of the circular saws, adjustments and maintenance of the
electric tool must be realised when the sawing machine is not powered, so before such tasks: Remove the plug of the
cord of the sawing machine from the mains socket!
Circular saw
Make sure the installed disc is not damaged, the cutting teeth are not broken, etc. In case any damage is detected, it is required
to replace the circular saw with a new one.
Do not use damaged or deformed circular saws!
Do not use circular saws made of high-speed steel!
Do not use abrasive discs!
Do not use discs which do not comply with the technical parameters indicated in this manual!
Do not use saws, whose body is thicker or whose set is smaller than the thickness of the splitting edge!
Do not use discs whose maximum acceptable rotational velocity is lower than 5500 rpm.
Select a circular saw designed for cutting of the given material. The more teeth hast the saw circular saw, the smoother the edges
of the saw cut will be. Saws with dozens of teeth are better suited for cutting of thinner materials, whose thickness is below 1 cm
and for soft wood.
Attention! Do not cut other materials than those indicated in the manual.
Installation and replacement of the circular saw (II)
Caution! Due to the risk of injury from sharp edges of the saw, all assembly operations must be carried out with protective gloves.
Caution! When replacing or assembling the saw, do not disassemble the saw blades!
Press the spindle lock button and use the key to slowly turn the spindle until the lock stops rotating the spindle. Use a wrench
to hold the locking button to unscrew the screw securing the circular saw blade. Remove the external mounting fl ange. Install a
circular saw on the inner mounting fl ange so that the saw hole is aligned with the protruding part of the fl ange. Fix the external
fi xing fl ange and tighten the fi xing screw.
Check that the circular saw has no side play and that it rotates freely without snagging on the saw blade guard. Try to do this by
turning the saw by hand by at least one full revolution.
Caution! Before installing the circular saw, thoroughly clean the place of installation (spindle and mounting fl anges), as well as the
interior of the shields from dust and chips generated during operation.
Adjustments of the cutting depth (III)
If required, the tool permits adjustments of the cutting depth, which is facilitated by the scaled guide (located at the back of the tool).
In order to do so, it is required to unscrew the lock located on the scaled guide, set the required cutting depth and lock the bolt.
Adjustments of the cutting angle (IV)
The tool permits cutting of planes at an angle between 0 and 45 . Set the required angle on the scale located at the front of the
O
tool and tighten the locking bolt.
O R I G I N A L I N S T R U C T I O N S
16