Publicidad
Idiomas disponibles
Idiomas disponibles
EN
• For a better wiping effect, the wiping module should
be used after sweeping or vacuuming the floor three
times.
• To refill water or clean the cloth while the appliance
is operating, pause it, remove and reinsert the wiping
module as described in steps 8 and 9. Do not move
or flip the appliance to avoid positioning errors and
map loss.
• The wiping function of the appliance is designed for
wiping and aids deep cleaning. However, it cannot
effectively remove stubborn dirt and thus replace
human power.
• We recommend soaking the wiping cloth before
mopping for better cleaning.
Note:
• The robotic vacuum cleaner cannot be used to
remove fluids.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
robot catches these wires.
CHARGING
Automatic mode: The appliance automatically returns to
the docking station after work. The dirt is sucked out of
the container. Automatic emptying of the dust container
can be set in the app.
Manual mode: When paused, press the button
briefly
to start charging or you can use your mobile app to charge
the appliance.
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates
a map and intelligently divides it into area (the map will
be created by scanning of adjacent areas 4x4 m, until the
map of the entire area has been scanned by the device)..
Then it sweeps the areas one after the other properly,
efficiently and thoroughly along the wall and plans a
curved / S-shaped cleaning path. After cleaning, the robot
automatically returns to the charging base.
Note: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
70
LOCAL CLEANING
If a local area needs more thorough cleaning, the user
specifies an area of 1.5 x 1.5 m that he/she wants to
clean on the map. The appliance automatically moves
to this area and starts cleaning it. If the device cannot be
controlled from the mobile app, relocate it manually to
the area you want to clean. Press long the charging button
(1.), the robot vacuum will perform local cleaning of the
area 1, 5 x 1, 5 m around its starting point.
ZONE CLEANING
Select the zones to be cleaned in the mobile app. This
selection can only be made after scanning the map and
saving it in the mobile app.
ROOM CLEANING
Use the mobile app to select the rooms you want to clean.
RESTRICTED ZONE
Use the mobile app to set up one or more restricted
areas. The robot will not clean in these restricted areas
and will clean in others.
Note: The robot may reach the restricted area due to
positioning errors, sensor errors or other reasons.
• A permanently restricted zone may be invalidated
due to a significant change in position of the charging
base and furniture. Therefore, try not to move the
robot or otherwise interfere with its work during
cleaning.
• The permanently restricted area will be revoked as
soon as the map is restored.
NO WIPING ZONE
Use the mobile app to select a no wiping zone. If the
appliance has a wiping module installed, it will not go to
this area. If the appliance only vacuums, it will go to this
area.
CLEANING PLANNING
You can set a fixed cleaning time using the mobile app.
The appliance will automatically start cleaning at the
specified time and will return to the docking station when
completed.
WI-FI RESET
If the mobile phone cannot connect to the appliance
due to a change in router and password configuration or
other reasons, press the button
and the button
3 seconds at the same time until you hear the "Reset WiFi"
and Wi-Fi indicator (17) starts flashing.
VR3550
CLEANING PERFORMANCE LEVEL/WATER DOSAGE
QUANTITY
You can select one of four cleaning performance levels
and four water dosage quantities in your mobile app.
Use the Autoboost mode to increase device´s cleaning
performance automatically, after it reaches the carpet
DAILY MAINTENANCE
Main brush (clean regularly)
1. Turn the appliance over and press the latch on the
main brush cover to pull it out.
2. Remove dust from inside and from inside the main
brush with a small brush and clean the main brush.
3. Reassemble the main brush and press firmly on the
cover until the latch clicks into place.
Side brush (clean regularly)
1. Turn the appliance over and pull the side brush up.
2. Remove hair and dirt and refit the side brush.
Note: Replace the side brushes every 3 to 6 months to
ensure its cleaning effect.
Dust container + filters (clean regularly)
1. Open the upper lid of the device.
2. Press the dust container unlocking button (19.) and
remove the container.
3. Remove the filters from the dust container and clean
them using the brush.
4. Press the dirt removal button and empty the contents
of the dirt container
Wiping module (clean after each use)
1. Remove and clean the cloth.
2. Wipe the water tank dry.
Sensors (clean regularly)
Clean the sensors with a soft cloth:
1. Side vertical sensor (6.)
2. Cliff sensors (8.)
3. Front laser sensors (3.)
4. Charging electrodes (9. + 1.4)
Rem.: Always switch off the robot vacuum (charging
base) before cleaning.
for
VR3550
EN
Battery
• The appliance is equipped with high-performance
lithium-ion
batteries.
To
maintain
battery
performance, keep the appliance charged every day.
• If the appliance is not used for a long time, turn it off
and store it properly. Charge it at least every 3 months
to prevent damage to the batteries due to excessive
discharge.
Firmware update
Use the mobile app to update the firmware. If new
firmware is detected, update as prompted. When
updating the firmware, the battery level should be ≥50 %
and the appliance must be placed in the docking station.
Docking station
• Regularly check the bag in the docking station. If the
bag is full, replace it with a new one.
• Clean the charging contacts and the suction opening.
71
Publicidad
