Introduction And Assembly; Humisteam Basic (Uey*); Dimensions And Weights; Opening The Packaging - Carel humiSteam Basic Serie Manual Del Usuario

1.1 humiSteam basic (UEY*)

Range of isothermal immersed electrode humidifi ers with backlit display
for the control and distribution of steam.
Models available (identifi able from the code shown on the product):
•
UE001, UE003, UE005, UE008, UE009, UE010, UE015, UE018 with steam
production capacity up to 18 kg/h (39.7 lb/h), water connections under
the base of the humidifi er;
•
UE025, UE035, UE045, UE065 with steam production capacity from 25
to 65 kg/h (55.1 to 144.3 lb/h), water connections on the side of the
humidifi er.

1.2 Dimensions and weights

Models UE001 to UE018
A
B
C
Fig. 1.a
UE001 to
UE008
dimensions A 365 (14.4) 365 (14.4) 545 (21.5)
mm (")
B 275 (10.8) 275 (10.8) 375 (14.8)
C 620 (24.4) 712 (28.0) 815 (32.0)
weights kg packaged 16 (35.3)
(lb)
empty 13,5 (29.8) 17 (37.5)
installed* 19 (41.9)
*: in operating conditions, fi lled with water
**: 230 Vac model

1.3 Opening the packaging

make sure the humidifi er is intact upon delivery and immediately
notify the transporter, in writing, of any damage that may be due to
careless or improper transport;
move the humidifi er to the site of installation before removing from
the packaging, grasping the neck only from underneath the base;
open the cardboard box, remove the protective material and remove
the humidifi er, keeping it vertical at all times.

1.4 Positioning

•
the unit is designed to be mounted on a wall that is strong enough to
support the weight in normal operating conditions (see Wall-mounting
below). Models UE025 to UE065 can stand on the fl oor;
•
to ensure correct steam distribution, position the humidifi er near the
point of steam distribution;
•
make sure the humidifi er is level, allowing the minimum clearances
(see Fig. 1.b) for maintenance operations.
Important Important : during operation the metal casing heats up and the
rear part resting against the wall may reach temperatures in
excess of 60 °C (140 °F) .

1. INTRODUCTION AND ASSEMBLY

Models UE025 to UE065
A
B
C
UE009 to UE025 to UE045** to
UE018 UE045 UE065
635 (25.0)
465 (18.3)
890 (35.0)
20 (44.0) 39 (86.0) 51 (112.4)
34 (74.9) 44 (97.0)
27 (59.5) 60,5 (133.4) 94 (207.2)
Tab. 1.a
Distances from walls
Models UE001 to UE018
≥ 200
(7.9")
≥ 200
≥ 200
(7.9")
(7.9")
≥ 700
(27.6")
≥ 400
(15.7")

1.5 Wall-mounting

Fit the humidifi er on the wall using the support bracket and the screw kit
supplied (for the dimensions in mm/inches see Fig. 1.d).
Assembly instructions:
1.
unscrew the wall bracket from the humidifi er bracket;
2. fasten the wall bracket (see Fig. 1.c), checking horizontal position with
a spirit level; if installed on a masonry wall, the plastic anchor plugs
(dia. 8 mm/0.31" ) and screws (dia. 5 mm x L= 50 mm/ 0.19" x L= 1.97"
) supplied can be used;
3. hang the appliance to the bracket using the slot on the top edge of the
rear of the appliance;
4.
secure the appliance to the wall through the hole in the centre on the
rear of the unit. For the weights and dimensions see Tab.1.a.
Models UE001 to UE065
7
Models UE025 to UE065
≥ 200
(7.9")
≥ 500
(16.4")
≥ 700
(27.6")
<0,5°
Fig. 1.b
X
bracket
Fig. 1.c
"UE BASIC" +030220632 - rel. 2.3 - 20.01.2009
ENG
≥ 200
(7.9")