Gaggenau VG231220DE Instrucciones De Montaje página 11

VG231220, VG231220DE
Total connected load, natural gas: 6 / 5,8 kW
¡
(only for NL gas G25-25 mbar)
Total connected load, electric: 10,0 W
¡
Changing the gas type
WARNING ‒ Risk of explosion!
Escaping gas may cause an explosion.
Never remove the gas valve shaft.
▶
In the event of damage or an unusual gas conver-
▶
sion, replace the entire gas valve. In this case, call
customer service.
Requirement: The appliance must only be converted
to a different type of gas by a licensed expert.
Switch off the power supply and the gas supply.
1.
The appliance can be converted to another type of
2.
gas listed on the rating plate using a conversion
kit.
Replace the main control nozzles.
3.
Adjust the gas valves using bypass screws.
4.
The correct combination for the relevant gas type
5.
→ Fig. can be found in the overview.
27
Removing appliance components
Remove the pan supports and all burner parts.
1.
Remove the control knob.
2.
→ Fig.
13
Undo the fastening screws on the burner.
3.
→ Fig.
14
Carefully lift the hob upwards and remove it.
4.
→ Fig.
15
Undo the fastening screws on the control panel.
5.
→ Fig.
16
First lift up the control panel slightly, then remove
6.
the connection cable before removing the control
panel completely.
→ Fig.
17
Remove the securing clips from the burner pipes.
7.
Pull out the burner pipes.
8.
Replacing the main control nozzles on the wok
burner
Unscrew the fastening screw on the air regulating
1.
sleeve.
Remove the nozzle retaining head.
2.
Pull off the nozzle w2 and O-ring for the inner
3.
burner ring by hand.
Unscrew the nozzle for the outer burner ring w1
4.
(WAF 10).
→ Fig.
18
Check that the O-ring is seated correctly in the
5.
new main control nozzle for the inner burner ring.
Fit the nozzle w2 onto the burner pipe.
6.
Screw the new main control nozzle for the outer
7.
burner ring w1 as far as it will go into the nozzle
retaining head.
Fit the nozzle retaining head onto the burner
8.
pipes.
Fit the securing clips.
9.
Adjusting the main control nozzles on the wok
burner
Unscrew the fastening screw.
1.
→ Fig.
19
Adjust the air regulating valve to the correct set-
2.
ting.
The setting depends on the gas type → Fig.
Tighten the fastening screw.
3.
Adjusting the gas valves
ATTENTION!
A bypass screw that has been over-tightened may
damage the appliance.
Do not over-tighten the bypass screws.
▶
If necessary, adjust the bypass screws M → Fig.
1.
using a Torx screwdriver.
27
up: The bypass screws must be flush with the top
2.
edge of the frame.
→ Fig.
20
down: Screw in the bypass screws fully.
3.
→ Fig.
21
Make sure that the FRD code matches the gas
4.
type → Fig.
→ Fig.
22
The FRD code cannot be changed.
Installing the appliance components
Connect the connection cable on the back of the
1.
control panel.
→ Fig.
23
Put the control panel in place and screw it on
2.
evenly.
→ Fig.
24
Put the hob in place and screw it on.
3.
→ Fig.
25
Attach the control knobs.
4.
→ Fig.
26
Fitting burner parts
Fit the burner parts and position them correctly.
▶
→ Fig.
11
Fitting the pan supports
Fit the pan supports and position them correctly.
▶
→ Fig.
12
Checking that the appliance is working after con-
version
After converting the gas type, check the appliance
1.
for leaks.
Make sure that yellow tips are not visible on the
2.
flames.
When turning the control knob quickly between
3.
the highest and the lowest setting, make sure that
the burner does not go out and that no flashback
occurs.
Documenting the gas type conversion
Attach the sticker showing the new gas type next
▶
to the rating plate on the appliance.
Connection to gas cylinder or liquid gas
tank
If the flame is large or unstable, check that the
▶
regulator of the gas cylinder or liquid gas tank is
working properly.
Note: You can install an overpressure safety device
that limits or cuts off the gas supply if the regulator
of the gas cylinder or liquid gas tank fails.
cs
Rozsah dodávky
Po vybalení zkontrolujte všechny díly na poškození
vzniklá při přepravě a jejich kompletnost.
→ Obr.
1
.
27
Bezpečnostní vzdálenosti
Dodržujte bezpečnostní vzdálenosti spotřebiče.
→ Obr.
2
.
27
11