Publicidad
Idiomas disponibles
Idiomas disponibles
Switching off
1. To switch off, release the on/off switch (2).
Continuous operation is not possible.
9.1.1
LED work lamp (14)
This product is equipped with an LED work lamp to illumi-
nate the immediate work area and improve visibility in
poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the light
source.
1. The LED work lamp (14) lights up automatically as
soon as the product is switched on.
9.2
Overload switch-off
In the event of overloading, the motor will switch itself off.
After a cool-down period (time varies) the motor can be
switched back on again.
9.3
Setting the mitre angle (Fig. 1, 7)
Note:
Use of the chip guard is not possible with a mitre cut.
1. Remove the chip guard (19) from the sliding shoe
(20), as described under 8.4, and the suction adapter
(16).
2. Loosen the Allen screw (7) with the Allen key (18).
3. Pull the base plate (6) back slightly.
4. Set the base plate (6) to the desired position (-45° –
+45°).
There are a total of 7 levels that can be set (-45°, -30°,
-15°, 0°, 15°, 30° and 45°).
5. Slide the base plate (6) forward into one of the latch
stops.
6. Tighten the Allen screw (7) with the Allen key (18).
9.4
Setting the pendulum stroke (Fig. 8)
With the pendulum stroke switch (5) it is possible to set
the pendulum movement of the saw blade (15).
The following positions are available for the pendulum
stroke switch (5):
0 -
No stroke
1 -
Low stroke
2 -
Moderate stroke
3 -
Powerful stroke
The optimum stroke strength can be determined by practi-
cal testing, with the following recommendations:
• Fine and clean cutting edges can be achieved with lit-
tle or no pendulum movement (level 1 or 0).
• For thin material, hard material (e.g. steel) and for
curve cutting also use level 0.
• Soft material (wood, plastic, etc.): Set the pendulum to
level 2 or 3.
Note:
With the pendulum stroke activated, work progress be-
comes increasingly faster.
9.5
Connecting external dust
extraction unit (Fig. 1, 9)
Note:
You can connect the suction hose of a vacuum cleaner
(with an outer diameter of 32mm and 35mm) directly to
the product without an adapter, if necessary.
9.5.1
1. Push the suction connection (17) into the rail between
the product and the base plate (6) as far as it will go.
2. Connect an approved dust extraction unit (not includ-
ed in the scope of delivery) to the extraction connec-
tion (17).
3. If the external dust extraction unit does not fit, use the
additional suction adapter (16) if necessary.
4. Switch on the product as described under 9.1.
9.5.2
1. Take off the vacuum hose from the suction adapter
(16) or from the suction connection (17).
2. Take the suction adapter (16) off from the product.
3. Remove the suction connection (17).
9.6
Plunge cuts (Fig. 1, 10)
Plunge cuts may only be made in soft materials such as
wood, aerated concrete, plasterboard, etc. However, this
requires some practice and is only possible with short
saw blades. Plunge cuts are only permitted if the mitre
angle is 0°.
1. Place the front edge of the base plate (6) flush on the
workpiece.
2. Slowly saw into the workpiece with a downward mo-
tion until the base plate (6) rests completely on the
workpiece.
3. Continue sawing along the cut line.
4. Switch off the saw and lift it off the workpiece when
finished.
9.7
Metal cuts
• Use a suitable coolant (cutting oil) when machining
metal. Violations can lead to significant blade wear.
The underside of the workpiece can be greased in-
stead of using a coolant. The scope of delivery in-
cludes a saw blade for wood, use suitable saw blades
for metal cuts.
10 Working instructions
• Check the material to be processed for foreign objects
such as nails, screws etc. and remove them.
• Ensure that the ventilation slots are not covered.
• Switch on the product and only then approach the ma-
terial to be processed.
• Switch the product off immediately if the saw blade
jams. Spread the already sawn gap with a suitable
tool and pull out the product.
• Adjust the saw blade and stroke rate to suit the mate-
rial to be processed.
www.scheppach.com
Connecting an external dust
extraction unit
Taking off the external dust
extraction unit
GB | 23
Publicidad
