SunPower Maxeon 3 SPR-MAX3-COM Serie Instrucciones De Seguridad E Instalación página 17

SunPower Maxeon 6 72 cells Commercial Solar Panel
(SPR-MAX6-XXX-COM)
0
50 150
296
A
TOP CLAMPS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
Long Side Moun ng,
Rails Parallel to
Moun ng Frame
Short Side Moun ng,
Rails Perpendicular to
Moun ng Frame
(End Mount)
Short Side Moun ng,
Point Supported
(End Mount)
Short Side Moun ng,
Rails Parallel to
Moun ng Frame
(End Mount)
1 In the cases where hybrid moun ng is necessary (combina on of long and short side moun ng), the lowest
design load values should be considered as allowable design load.
2 Test loads are for informa on purposes only, design loads should be considered for the project design.
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
par es, unless there is a formal authoriza on by Maxeon.
©2024 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Safety and Installation Instructions - Document 001-15497 Rev.AB
536 825
400 mm
1200 mm
1423 mm
1653 mm
2047 mm
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
Moun ng Zone
Test Load Design Load
Loca ons
(distance from corner Downward/Upward Downward/Upward
(Pa) (Pa)
in mm)
+1800/-1800 +1200/-1200
50 - 150
150 - 296
+2400/-2400 +1600/-1600
296 - 536 +5400/-3600 +3600/-2400
536 - 825 +2400/-2400
+1600/-1600
50 - 150 +1800/-1800 +1200/-1200
150 - 296 +2400/-2400 +1600/-1600
296 - 536 +5400/-2400 +3600/-1600
536 - 825
+2400/-2400 +1600/-1600
50 - 150 +1200/-1200
+1800/-1800
150 - 296 +1600/-1600
+2400/-2400
296 - 536
+5400/-2400 +3600/-1600
536 - 825 +2400/-2400
+1600/-1600
0 - 350
+2400/-1600 +1600/-1067
+1800/-1600 +1200/-1067
0 - 350
0 - 350 +1800/-1600 +1200/-1067
MAXEON SOLAR TECHNOLOGIES, LTD.
825 536
B
A - MLSD Holes
B - Moun ng Holes (16X Ø6.8mm)
C - Ground Holes (4X Ø4.2mm)
GEN 5.6 FRAME PROFILE
SIDE FRAME PROFILE
35 mm
32 mm
BOLTS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on
Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
4 Rails must not be under the junc on box.
5 Bo om Flange Moun ng
6 Range indicates posi oning of the clamps and not the rails.
7 Slight bending may occur due to weight of the module.
0
150 50
296
C
END FRAME PROFILE
35 mm
32 mm
Moun ng Zone
Test Load
Design Load
Loca ons
(distance from corner
Downward/Upward Downward/Upward
(Pa) (Pa)
in mm)
+5400/-4500
1423mm Holes +3600/-3000
1200mm Holes +3600/-3000
+5400/-4500
+2400/-2400 +1600/-1600
400mm Holes
1423mm Holes +2400/-4500 +1600/-3000
+2400/-4500 +1600/-3000
1200mm Holes
400mm Holes +2400/-2400 +1600/-1600
EN