Sansui AU-X417R Manual De Instrucciones página 5

Thank you for purchasing this fine SANSUI! product. Taking the
time to read these operating instructions carefully before use
will acquaint you fully with all its features and help ensure
optimum performance.
Precautions
Power plug
When disconnecting the power cord from the power outlet, always
take hold of the plug, and not the wire, and pull free. Never connect or
disconnect the power plug with wet hands since you may receive an
electric shock.
* Remember to disconnect the power plug from the power outlet
when you do not intend to use the unit for a prolonged period of
time.
Do not remove the case and bottom panel
Any inspections or adjustments inside the unit may lead to
malfunctions and electric shocks. Do not touch any of the inside parts.
SANSUI's warranty is not effective if a deterioration in the unit's
performance results from remodeling inside.
Do not block the ventilation holes
Do not block the ventilation holes on the top of the unit by placing
records or other objects over them.
This will increase the inside temperature and may lead to a failure or
malfunction.
Installation precautions
Do not instal! the unit in any of the following locations since this may
result in a deterioration in performance or malfunction:
* Locations exposed to direct sunlight or near objects
radiating heat such as heating appliances.
Locations exposed to moisture or humidity.
Locations with poor ventilation exposed to dust and dirt.
Locations which are unstable and not perfectly flat
or which are susceptible to vibration.
Do not wipe with thinners
Wipe the panels and case from time to time with a soft cloth. Using
any kind of thinner, alcohol or volatile liquid will mar the surface, cause
blotching on the exterior and erase the markings and should therefore
be avoided.
Do not use insecticide sprays in the vicinity.
This unit dissipates the heat most effectively when installed on
a flat surface. Do not stand it up or install it at an angle.
Before connecting the power plug
Before connecting the power plug to an electrical outlet,
check to be sure that the unit is set to the proper voltage for
your area. If the voltage of the unit is improperly set, fire
hazard or damage to the unit may result.
lf the unit is to be used in an area where the power requirements
are different, make sure you consult your nearest authorized
SANSUI Service Station.
* In order to simplify the explanation illustrations may
sometimes differ from the originals.
Connections
Connection precautions
* When connecting, either disconnect the power plug from the
power outlet or turn off the unit's power using the POWER switch.
Check the left and right channels and connect properly (L to L and R
to R).
Insert the plugs securely. Improper connection can lead to the
generation of noise.
*
*
Turntable
Connect the turntable's output cord L (white) plug to the L PHONO
terminal and the R (red) plug to the R terminal.
\f your turntable is equipped with a grounding cable, connect it to the
unit's GND terminal. But disconnect it if you notice increased hum.
* If you use the turntable alongside this unit, hum and noise pickup
may sometimes occur. In such a case, install the turntable at a
position where hum and noise are not picked up.
Compact disc player
Connect the CD terminals to the OUTPUT terminals on the compact
dise player using the pin-plug cord.
Tuner
Connect the TUNER terminals to the OUTPUT terminals on the tuner
using the pin-plug cord.
LINE terminals
The LINE terminals have an electrical performance which is equivalent
to that of the CD terminals and TUNER terminals, which means that
they can be used as the audio output terminals for a video disc player
or TV tuner.
Connect the LINE terminals to the OUTPUT terminals on the
component using the pin-plug cord.
Tape deck
There are two sets of TAPE terminals for connecting a tape deck. This
permits up to two tape decks to be connected to perform
simultaneous recording or tape dubbing.
Recording connections : Connect the TAPE REC terminals to the
input (LINE IN) terminals on the tape deck using the pin-plug cord.
Playback connections : Connect the TAPE PLAY terminals to the
output (LINE OUT) terminals on the tape deck using the pin-plug
cord.
AC outlets
This unit is provided with auxiliary AC outlets which are handy for
connecting a tuner, tape deck or turntable to supply power to these
units.
SWITCHED (250W capacity) : The power of the connected
components is switched on and off when the unit's POWER switch
is operated.
(Models sold on the European market require a single
SWITCHED-type AC outlet.)
It is extremely dangerous to connect an electrical appliante having a
power consumption exceeding the specified capacity. Before
connecting the appliance or components, check its power
consumption rating.
« Ahigh voitage flows to the AC outlets and so hairpins or other
metal objects must not be inserted since this will result in an
electric shock.
NOTE : Depending on the laws and regulation enforced locally, models
without AC outlets may be supplied to some areas. Also, depending
on the sales area, the shape of the AC outlets and their capacity may
differ.
:
j t
i
i
4
;
1
3