YATO YT-82555 Manual Original página 18

EN
socket at the back of the gun housing (III). Attach the bayoneted tip to the air outlet of the compressor housing. The end of the hose
should be placed on the air outlet and then rotated so that the seat pins engage with the holes of the hose end (IV).
The compressor housing allows the hose to be rolled up for transport and storage of the unit. Before starting, the hose should be
completely unwound.
Filling and assembly of the paint container
Unscrew the paint container. Push the suction pipe fi rmly into the mounting opening (V). The end of the suction pipe is bend to
help empty the container more accurately when holding the gun at an angle, e.g. when painting fl oors or ceilings. When turning
the suction pipe, point the bent end of the pipe in the opposite direction to the expected inclination of the gun. Fill the container
with paint of suitable viscosity. Do not exceed the upper capacity marker of the paint container. Carefully screw the container to
the gun and tighten it to seal the connection.
GUN OPERATION
The gun is not suitable for spraying the following paints:
High-density paints – fl ow time through the viscometer above 100 s.
Paints containing abrasives such as red lead oxide.
Coarse-grained paints.
Corrosive and base paints.
All adjustments of the nozzle must be carried out with the power supply disconnected. To do this, unplug the power cord plug
from the socket.
Spray adjustment (VI)
The gun nozzle allows to set the spraying plane and width of the spraying material. The spraying plane can be set by rotating the
air nozzles. The air nozzles in a vertical position allow to obtain horizontal spraying plane, and nozzles in a horizontal position
allow to obtain vertical spraying plane of the coating material. Setting the nozzles at an angle of 45 degrees will result in obtaining
a point spraying plane of the coating material.
Do not place the adjustment elements in positions other than those described in the manual.
CAUTION! Do not press the spray gun trigger button while adjusting the air nozzles.
Adjustment of the amount of spraying of coating material (VII)
Behind the trigger / on/off switch, there is a control knob that limits the depth of the trigger pull. The deeper the trigger is pressed,
the more spray material comes out of the spray gun nozzle. Turning the knob clockwise increases the amount of coating material,
turning the knob counter clockwise decreases the amount of coating material. The trigger has a mark to facilitate the adjustment.
Switching on/off
Assemble the unit according to the instructions.
Fill the container with the coating material according to the procedure described above.
Make sure that the voltage on the nameplate corresponds to the mains voltage.
Check that the tool switch is in the off position – O.
Make sure that the gun trigger is not pressed.
Plug the power cord plug into the mains socket.
Turn the device on with the switch, move it to the on position – I. Point the gun at a safe place and press the trigger. Adjust the
amount of spray material, if necessary, according to the adjustment procedure.
The spraying will stop when the pressure on the trigger of the gun is released.
The device is switched off when the switch is set to the off position.
Painting
It is recommended that the fi rst attempts of spraying the coating material be carried out on the test surface. This will avoid damage
to the work area.
Make sure that all surfaces not to be covered are well covered. Make sure that the surface to be covered is clean, dry, degreased
and free from dust.
Keep the unit upright so that the nozzle outlet is approximately 20 cm from the surface to be sprayed.
Move the spray gun sideways or up and down so that it is always at a constant distance from the surface to be sprayed (VIII). Start
moving the gun and only then pull the trigger. Release the pressure on the trigger before completing the movement of the gun
(IX). Moving the spray gun with a steady motion, changing pace or stopping the spray gun during spraying will result in uneven
distribution of the coating material.
Avoid tilting the gun both horizontally and vertically (X). This will result in an uneven distribution of the coating material.
O R I G I N A L I N S T R U C T I O N S
18