Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION
For the installation instructions, follow the drawings printed on the package. Drawings are for illustration purposes only. May
not reflect actual product. Not to scale.
RECOMMENDATIONS DURING THE INSTALLATION
• Use of an extension cord or multi-plug adaptor with the spa heater is dangerous and can cause the plug to overheat, causing damage to the equipment
and surrounding items.
• Keep the spa away from the rest area to minimize noise disturbance.
• Keep at least 1m clearance around the spa.
• We don't recommend using sea water to fill the pool. Sea water can corrode the internal metal components due to the high concentration of salt.
• The filtration system of the spa is designed to be used only with the filter cartridge. Any other component added inside the filter set can cause damage
to the filtration system of the spa. This will not be covered by customer service.
INFLATION INFORMATION
Only For Inflatable Spa Liner or Inflatable Cover:
• When inflating, you will notice that air will be expelled from the area where the air hose connects to the pump, this is
normal for technique requirements.
• Don't cover the holes on the base of the inflation hose, the inflation hose is designed to inflate the spa to the correct
pressure. This operation will over inflate the liner and damage the structure.
• Do not use an air compressor to inflate the spa.
• Do not drag the pool on rough ground as this may cause damage to the spa liner. Inflation time for reference only.
HAND PUMP PRESSURE GAUGE
Only For Fortifiber Spa:
• The air pressure gauge of the hand pump only shows the air pressure higher than
5 psi, which is normal. When the air pressure in the product is lower than 5 psi, the air pressure gauge will not show a value.
AIR VALVE CHECK
Only For Fortifiber Spa：
• If the air valve is loose, use the provided wrench to fasten the air valve following these steps: With one hand, hold the backside of the air valve from the
inner side of the spa wall and turn the wrench clockwise.
• Do not adjust the air valve connector when the spa is in use.
USING THE SPA
CONTROL PANEL
LOCK/UNLOCK BUTTON: The pump has a 5-minute auto-lock, this light will turn on. To lock or unlock the pump, press the lock/unlock
button for 2 seconds.
POWER-SAVING TIMER BUTTON: Designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa.
follow these steps to activate the POWER-SAVING function.
Press the
button and the
Press the
or
Press the
button again to confirm the heating duration.
After setting the heating duration, the
Press the
or
function. If the timer is set to 0 hour, the heating system will activate immediately.
Press
button again or simply touch nothing for 10 seconds to confirm the setting. The
heater activation will begin. The screen flashes the current temperature and time alternately.
To modify the timer settings: Press the
Cancel the setting: Press the
When the power saving function is activated, all other functions (massage, filtration) except the heating can be used.
The POWER-SAVING function in not an automatic function: after one complete cycle (waiting time plus heating function), this function
must set again.
HEAT BUTTON:Press
When the light is green, the water reached the set temperature.
If the heating system is activated, the filtration system will automatically start.
After turning off the heating system, the filtration system will continue to operate.
MASSAGE SYSTEM BUTTON:Press
The light of the button becomes red when activated.
Do not run the massage system when the cover is attached, air can accumulate inside the spa and cause irreparable damage
to the cover. Heat and massage system can be activated at the same time.
FOR SPA EQUIPPED WITH Wi-Fi ONLY
2-LEVEL MASSAGE REGULATION: Push once for the full power massage; the display will show L1. Push it again for a lower power
massage; the display will show L2. Push it a third time to shut the massage function off.
When inflating the spa liner, make sure that the massage function is running at full power.
AIRJET
LED starts to flash.
button to adjust the heating duration (From 1-999 hours).
LED starts to flash.
button to set the time (From 0-999 hours). This setting defines the waiting hours before the activation of the heating
button and use the
button for 2 seconds.
button to activate the heating system. When the light of the
button to activate the massage system, which has a 30-minute auto-shutoff feature.
AIRJET WITH Wi-Fi
or
button to adjust.
13
LED will light steadily, and the countdown to
button is red, the heating system is activated.
Publicidad
