Pioneer VSX-924-K Guia De Inicio Rapido página 9

Basic playback
Multichannel playback
STANDBY/ON SOURCE
ALL ZONE STBY
RECEIVER SUB ZONE CONTROL
MAIN Z2 Z3 HDZ
SOURCE CONTROL
BD DVD SAT HDMI
2 USB ADPT ROKU
iPod BT MHL NET
ALL
TUNER TV CD
VOLUME
TV VOL
INPUT
STATUS MUTE
OUT P.
AUDIO P. VIDEO P.
TOP TOOLS
MENU MENU
ENTER
HOME
MENU RETURN
3 LISTENING MODE
AUTO SURR ADV CH LV.
MPX BAND PTY
PRESET TUNE
AUDIO
1 2 3
Fav
DISP
4 5 6
7 8 9 CH
D.ACCESS CLASS
CLR 0 ENTER CH
DIMMER SLEEP RCU SETUP
RECEIVER
1
Switch on the playback component.
E.g.) Turn the Blu-ray Disc player connected to the HDMI
BD IN terminal on.
2
Switch the input of the receiver.
E.g.) Press BD to select the BD input.
3
Press AUTO to select 'AUTO SURROUND'.
Also press SURR or ADV for multichannel playback. Select
your preferred listening mode.
4
Start the playback component's playback.
5
E.g.) Start playback of the Blu-ray Disc player.
5
Use VOLUME +/– to adjust the volume level.
• When a sound can not be heard from center and rear
speakers, press SURR or ADV to change listening modes.
E.g.) Press the ADV button for several times to select
EXT.STEREO.
• When there is no sound from the subwoofer
Cause – The front speaker is set to LARGE.
When a 2-channel audio source is input, the low-frequency
component is not output from the subwoofer but is output
from the front speaker.
Solution – To output from the subwoofer, change the
speaker setting.
Method 1: Change the front speaker setting to SMALL.
The low-frequency component is not output from the front
speaker but is output from the subwoofer. When the low-
frequency playback capability of the front speaker is high,
we recommend the setting not be changed.
Method 2: Change the subwoofer setting to PLUS.
The low-frequency component is output from the front
speaker and subwoofer. For that reason, low sounds
are sometimes output too much. In such a case, we
recommend not to change or to change to Method 1.
• For details, see "Speaker Setting" of the operating
instructions.
• When no sound is emitted, increase the volume to
approximately –30 dB.
Note
• When the remote control cannot be used to operate the unit
– When operating the receiver, press MAIN RECEIVER
before using it.
– When operating functions such as the network, TUNER, or
iPod, press the appropriate function button (NET, TUNER,
iPod, etc.) before using.
Listening to the radio
1
Press TUNER to select the tuner.
If necessary, press BAND to change the band (FM or AM).
2
Press TUNE +/– to tune to a station.
• Press and hold TUNE +/– for about a second. The receiver
will start searching for the next station.
• If you're listening to an FM station but the reception is
weak, press MPX to select FM MONO and set the receiver
to the mono reception mode.
Saving station presets
If you often listen to a particular radio station, it's convenient to
have the receiver store the frequency for easy recall whenever
you want to listen to that station.
1
Press TOOLS while receiving a signal from the
station you want to store.
The preset number is blinking.
2
Press PRESET +/– to select the station preset
you want, then press ENTER.
The preset number stop blinking and the receiver stores
the station.
Listening to station presets
You will need to have some presets stored to do this.
 Press PRESET +/– to select the station preset
you want.
9