Emerson AVENTICS AF2 Descripción De Sistema página 11

1 About this documentation
These instructions contain important information for the safe and proper han-
dling of the product.
This documentation is a supplement to the applicable assembly instructions.
Read the assembly instructions completely before working with the product.
1.1 Documentation validity
This documentation is intended for:
Programmers, service personnel, system owners
This documentation provides supplementary information for handling the follow-
ing product variants of series AF2 and 652/653:
Series Product variant
AF2 Sensor/filter combination
(AS)
High-flow sensor (HF)
652 Filter product variant
Pipe product variant
653 Filter product variant
Pipe product variant
1.2 Additional documentation
Observe the following related documents:
• Manufacturer's system documentation
• Documentation of other system components
• Assembly instructions (R412026496 or 549411)
1.3 Abbreviations used
This documentation uses the following abbreviations:
Abbreviation Meaning
ABS Acrylonitrile butadiene styrene
GF Fiberglass
HF High flow
MBE Full scale value
MQTT Message Queuing Telemetry Transport
MTTF Mean Time To Failure
NPT National Taper Pipe
OLED Organic Light Emitting Diode
OPC UA Open Platform Communications Unified Architecture
PA Polyamide
PC Polycarbonate
PPE Personal protective equipment
Pt Platinum measuring resistor
2 Safety
2.1 About this chapter
• Read the chapter Safety of the assembly instructions and this documentation
completely before working with the product.
• Keep this documentation in a location where it is accessible to all users at all
times.
3 Data and parameters
3.1 Notes on safety
• Do not make parameter changes during operation (injury prevention).
AVENTICS™ AF2 | R412028957-BAL-001-AB | English
3.2 Parameter data
3.2.1 General settings
The parameter settings in this section apply to all variants of the product.
General
Objective
Make settings
Display
Objective
Interface
Set the units
IO-Link
Ethernet
IO-Link
Ethernet
IO-Link (A)
Ethernet (B)
IO-Link (A)
Ethernet (B)
IO-Link (A)
Set the display for screen 1.1
Ethernet (B)
IO-Link (A)
Set the display for screen 1.2
Ethernet (B)
Set the display for screen 1.3
Set the display for screen 2.1,
2.2, and 2.3
Optimize readability
Activate the screen saver
Switch off the display
Setting the brightness
Assign PIN to protect against
operation and manipulation
Fig. 1
Menu
Standard screen
Submenu
Units
Pages
Pages
Pages
Pages
Rotation
ScreenSaver
AutoOff
Brightness
Display Pin
Display Units MassFlowRat
FlowVelocity
Volume
VolFlowRate
Mass
Energy
Temperature
Pressure
Option
Press and hold any arrow button for
at least 2 seconds and make your
settings in the respective menu.
Option
Select from the following menus:
• MassFlowRate
• FlowVelocity
• Volume
• VolFlowRate
• Mass
• Energy
• Temperature
• Pressure
• Select Disp1Top
• Select Disp1Btm
• Select Disp2Top
• Select Disp2Btm
• Select Disp3Top
• Select Disp3Btm
Select display parameters in the Dis-
pHistory menu
Set the display to 0°, 90°, 180°, or
270°
Set the time for screen saver activa-
tion
Set the time for switching off the
display
Setting the brightness in percent
Assign 4-digit PIN
kg / h
kg / min
g / s
abort store
m / s
fps
abort store
m 3
ft³
L
abort store
m / h
3
ft / min
3
ft / s
3
L / min
L / s
m 3 / min
abort
store
kg
abort store
kWh
abort store
°C
°F
abort store
bar
psi
abort store
11