Publicidad
Idiomas disponibles
Idiomas disponibles
REAR PANEL
1
2
REM. WALL PANEL
CH 1
EMERGENCY IN
CHIME
VOX 1
VOX 2
CH 1
PHANTOM
CHIME
PHANTOM
48 V
CH 1
48 V
VOX 2
LINE
MIC
CHIME
REMOTE MUTE
22
21
18
1.- VOX 1/VOX 2/VOX 3: controls for sensitivity adjustment to give priority to the EMERGENCY IN,
CH 1, and CH 2-4 inputs respectively over the other signals. Depending on this setting, the signal level
required at the inputs to cut audio from other sources will be higher or lower. Please note the order of
priority of the amplifier inputs, for more information see OPERATION - INPUT PRIORITY.
2.- REM. WALL PANEL: connection port for remote wall panel, RJ45 connector. For more information see
section OPERATION - REMOTE WALL PANEL INPUT.
a bc d
3.- CH 1|PAGING MIC, CH 2, CH 3, CH 4: VOX audio inputs, balanced combo connectors (XLR and
6.3 mm jack) and euroblock (20). In addition, these inputs have a DIP switch (19) to adjust the sensitivity
of the MIC/LINE input, activate phantom power and enable/disable VOX priority (VOX 2 for CH 1|PAGING
MIC and VOX 3 for CH 2, CH 3 and CH 4) and CHIME priority (CHIME CH 1 for CH 1|PAGING MIC and
CHIME CH 2-4 for CH 2, CH 3 and CH 4).
4.- AUX 1/AUX 2/AUX 3: stereo auxiliary inputs for connection of audio devices such as mixers, computers,
etc. 2 x RCA connectors.
5.- REC OUT: stereo recording output with line level, 2 x RCA connectors.
6.- PRE OUT/AMP IN: pre-amplifier stage signal output (PRE OUT) and amplifier stage input (AMP IN),
RCA connectors. These inputs and outputs have a jumper to connect these 2 stages for the equipment
to function as a whole. If you want to use only the pre-amp stage, remove the jumper and connect your
amplifier to the PRE OUT output; or if you want to use the amp stage, remove the jumper and connect
your mixer/pre-amp output to the AMP IN input.
7.- ATTENUATOR PRIORITY - 3 WIRE: 100 V audio output for message priority on 3-wire attenuators. For
more information, see section OPERATION - 3rd WIRE PRIORITY.
8.- ATTENUATOR PRIORITY - 24 V: 24 V output for message priority on attenuators with priority relay
(4-wire attenuators). This output is at 0 V if no priority is activated, and will provide 24 V when priority is
activated. For more information, see section OPERATION - 24 V PRIORITY.
9.- FM ANTENNA: FM antenna connection input.
10.- TONE CONTROL - BASS: 100 Hz cut-off frequency low pass filter that attenuates/enhances
low frequencies.
11.- TONE CONTROL - TREBLE: high pass filter with 10 kHz cut-off frequency which attenuates/enhances
high frequencies.
12.- BLUETOOTH ANT: Bluetooth signal antenna.
13.- AC SELECT: power supply voltage selector. If you need to change the voltage you should be aware
that the fuse must be modified as specified on the product.
14.- 115/230 V amplifier power supply input .
15.- ZONE MICROPHONE: port for zone microphone connection, RJ45 connector. For further information
see section OPERATION - ZONE MICROPHONE INPUT.
3
CH 2
CH 3
CH 4
CHIME
VOX 3
CH 2-4
CHIME
PHANTOM
CHIME
PHANTOM
CHIME
CH 2-4
48 V
CH 2-4
48 V
CH 2-4
VOX 3
VOX 3
VOX 3
LINE
LINE
LINE
MIC
MIC
MIC
CHIME
CHIME
CHIME
20
19 18
a
b
4
5 6
7 8
AUX 1
AUX 2
AUX 3
REC OUT
PRE AMP
VOICE PRIORITY (VOX)
1
EMERGENCY IN | REM. MUTE
2
ZONE MICROPHONE
3
REMOTE WALL PANEL
ATTENUATOR PRIORITY
3 WIRE
24 V
100 V
R
R
R
R
PRE OUT
ZONE OUTPUT
ALL ZONES: 240 W RMS (MAX)
EACH ZONE: 240 W RMS (MAX)
ZONE 4 ZONE 3 ZONE 2 ZONE 1
L
L
L
L
AMP IN
17
- 3 -
9
10
11
12
FM ANTENNA
BLUETOOTH® ANT.
4
CH 1 | PAGING MIC
5
CH2 | CH3 | CH 4
6
AUX | PLAYER
TONE CONTROL
MAX-240Z
PA MIXING AMPLIFIER
BASS
TREBLE
ZONE MICROPHONE
SPEAKER OUTPUT
RS-485 + AUDIO
240 W RMS
~115 V AC, 50/60 Hz, FUSE: T8 A 250 V
~230 V AC, 50/60 Hz, FUSE: T4 A 250 V
POWER CONSUMPTION: 345 W
16
15
EN
13
AC SELECT
14
Publicidad
