Publicidad
Idiomas disponibles
Idiomas disponibles
Inserting the batteries:
1. You will need two Mignon (AA) batteries.
2. Open the cover of the battery compartment
below the PIR sensor by sliding it downwards.
3. Open the battery compartment by lifting up the latch.
4. Insert the batteries. Pay attention to the polarity. The mi-
nus end of the battery always connects to the spring in the
battery compartment.
5. Close the battery compartment
rubber sealing is in the groove and has not been twisted.
6. Slip the cover of the battery compartment back on.
Assembly:
1. Screw the plastic tube to the connector
the device.
2. Screw the metal spit to the plastic tube
3. Screw the quick connector for the garden hose to the metal
spit
.
4. Screw the spraying unit
5. The repellent can now be set up in the garden or near the
pond.
Operation:
To set up the Water Repellent choose a spot that will oversee
the area you want to clear of animals. Make sure to look for a
position where the animals will walk across the sensors view-
ing area rather than walking directly towards the sensor. Make
sure that the view of the sensor is not obstructed by leaves
or foliage and that the surface of the sensor is clean. When
adjusting sensor sensitivity you need to consider what kind of
animal you want to scare away and the distance of detection
(see below). It is possible to adjust the angle and the distance
of the waterspout. Make sure that the sensor has a stable
stand, as the recoil during the waterspout can be quite strong.
Place the ground spit into the ground. If the earth is too hard
we recommend to soften it by soaking it with water. The sen-
sor should not be higher than 1 m above the area that is being
controlled. If you want to place the device in an area that has
no soil, we recommend the use of an umbrella stand.
Note: False alarms can be triggered by objects that are warmer
than the surroundings, by strong water movement, by rapid
temperature changes and by house pets. On very hot days it
may occur that an animal is not detected as the surrounding
temperature is equal to that of the body temperature. This
function is normal for a PIR sensor.
Connect your garden hose to the quick connector on the spike
. Make sure that the hose and all connections are in good
condition and that there is no leakage. Make sure that there is
no sand or other debris is in the garden hose. If you do not want
to use the second outlet in the spike, then close this with the
supplied cap
. You should check the function of the device,
before opening the water tap. Switch the device to position 9
8
located
. Make sure that the
at the bottom of
.
to the top of the device.
and wave your hand in front of the motion sensor. If you hear
a silent click, then the device has been activated and the valve
for the water has switched. Open your water tap to full.
Controlling the waterspout:
The motion sensor
has a horizontal detection angle of
100° and vertical detection angle of 65°. With a water pressu-
re of 8 bar, the waterspout can reach up to 10 m. The distance
can be adjusted and reduced. This should be done on-site.
There are generally two ways of adjusting the water spray:
• D istance: turn the plastic screw the top of the sprinkler
unit
. The further the water-blocker
shorter the distance of the water spray.
• S cattering angle: at the base of the sprinkler unit you will
find two clips
/
limiting the scattering angle of the
spray unit. These can be easily turned and adjusted when
they are slightly pulled apart. Each clip defines the stop-
per for left
and right
When this hits one of the clips it will change the direction
of the sway.
Adjusting the sensitivity of the motion sensor:
At the back of the device you will find the on-off/sensitivity
button
. The adjustments are also dependent on the sur-
roundings and the activity of the sun.
• Mode 0 (full left): the device is switched off but will still
charge the batteries through the solar panel.
• Mode 1 – 9: Increases the sensitivity of the motion sensor.
Tip: if you want to reduce or direct the detecting angle of the
sensor you can do this by covering parts of the lens with a
light proof, adhesive foil.
3 m detection: mode 5 – 7
6 m detection: mode 8 – 9
Small animals
is extended, the
. The metal clip is the detector.
Publicidad
