EN GLIS H
R E . C O R . D . 5 1 & 5 2 - 1 0 2 & 1 0 3
(1)
Ready / Standby
: to switch from Standby Mode to Ready Mode and
key
vice versa. It is necessary to keep it pressed for
two seconds.
I n C on f i gu ra t i on M o de t h i s k e y w or k s a s
confirmation key (OK).
(2)
Left drink full dose
: to dispense a full dose of drink from the left
key
dispensing group.
In Configuration Mode this key works as UP key
().
(3)
Left drink half dose
: to dispense half a dose of drink from the left
key
dispensing group.
In Configuration Mode this key works as DOWN
key ().
(9)
Left water key
: to dispense water from left dispensing group.
In Configuration Mode this key works as CANC
key (C).
(5)
Right drink full
: to dispense a full dose of drink from the right
dose key
dispensing group.
(6)
Right drink half
: to dispense half a dose of drink from the right
dose key
dispensing group.
(7)
Right water key
: To dispense water from the right dispensing
group.
(8)
Display
(9)
Main switch
: To power On and Off the dispenser
(10) Smart Card reader
: (see paragraph 5. 5 SMART CARD)
(optional)
5. 3 USING THE DISPENSER
1 Prepare the dispenser as described above (see paragraph
5. 1 DISPENSER SET UP).
2 Power ON the dispenser using main switch. The current
software version will be shown on the display for some
seconds, once that the starting cycle will be expired the
dispenser will be in Standby mode and on the display the
following message will be shown:
In Standby Mode water is not heated and dispensing is not
available. The only functions available are Configuration Mode
(see paragraph 5. 4 CONFIGURATION MODE) and Smart Card
reading (see paragraph 5. 5 SMART CARD).
3 Switch the dispenser to Ready Mode by pressing key (1) for
two seconds. The following message will be shown:
HEATING
IN PROGRES
During water heating dispensing is not available except for
water only.
4 When water will be at the set temperature (default 80°C)
dispensing will be available and the following message will be
shown:
READY
IMPORTANT
Pressing any key during dispensing will immediately
stop the current dispensing cycle.
5 After each dispensing cycle it can be necessary to wait for
some seconds until when the set water temperature is restored.
OFF
80°C
5. 4 CONFIGURATION MODE
When the dispenser is in Stand-by Mode by pressing together
keys (OK) and () for two seconds it is possible to pass to
Configuration Mode. In this mode it is possible to set the
dispenser. The Configuration Menu has the following structure:
LANGUAGE SETTING
ITALIANO
ENGLISH
FRANCAIS
DEUTCH
ESPANOL
DOSE SETTING
DOSE 1 SETTING
WATER = 10 S
POWDER = 5 S
WATER RED.= 50 %
POWDER RED.= 50 %
DOSE 2 SETTING
WATER = 10 S
POWDER = 5 S
WATER RED.= 50 %
POWDWER RED.= 50 %
SETTING DOSE 1 + 2
WATER = 10 S
POWDER 1 = 5 S
POWDER 2 = 4 S
WATER RED.= 50 %
POWDWER RED.= 50 %
WATER HEATER SETTING
TEMPERATURE SCALE °C / °F
WATER HEATER 80 °C
TEMPERATURE DISPLAY
FILTER LIFE
COUNTERS
DOSE 1 COUNTER
TOTAL
PARTIAL
RESET
DOSE 2 COUNTER
TOTAL
PARTIAL
RESET
DOSE 1+2 COUNTER
TOTAL
PARTIAL
RESET
FILTER COUNTER
PASSWORD CONTROL
ACTIVATE PASSWORD
PARAMETERS SETTINGS
SMARTCARD SETTING
SMARTCARD CODE
BACKUP
CREDIT CONTROL
REMOTE CONTROL
ACTIVATION
PIN NUMBER
SERVER NUMBER
SMS AT POWER ON
TIME OF TRANSMISSION
VERIFY SIGNAL
SERIAL NUMBER
CUSTOMER CODE
Using the following keys it is possible to navigate into the
Configuration Menu:
(1)
Ready / Standby
: Confirmation key (OK). To confirm the current
key
selection and to go one level down into the
Configuration Menu.
(2)
R i g h t d r i n k f u l l
: UP key
dose key
Menu.
(3)
R i g h t d r i n k h a l f
: D O W N k e y ( ) . T o s c r o l l D o w n i n t o t h e
dose key
Configuration Menu.
(4)
Right water key
: CANC key (C). To cancel the current selection and
to return one level up into the Configuration Menu.
The available options of the Configuration Menu are the
following:
LANGUAGE SETTING: to set current language. Available
options: Italian and English.
DOSE SETTING: to set the dispensing times of water and
powders for all the available drinks.
WATER HEATER SETTING: to select the temperature scale,
Centigrade (°C) or Fahrenheit (°F), to set the desired water
temperature, to show the current water temperature on the
display or not and to set the water filter life (in dispensing
12
*** IF PRESENT ***
*** IF PRESENT ***
*** IF PRESENT ***
*** IF PRESENT ***
(
)
. To scroll Up into the Configuration