Oster 2143024 Manual De Usuario página 4

10. Plug the power cord into a 120 Volt AC electrical outlet.
11. Press the Power Button to turn the blender on. The power light will
blink, indicating the product is active and ready to use.
12. Select the desired Pre-Programmed setting or Manual Setting. To change
your selection, press Pulse followed by another Pre-Programmed Setting
or Manual Setting.
®
13. Your Oster Blender features 2 pre-programmed settings for superior
results at the touch of a button. Simply select one of the Pre-Programmed
Settings (Smoothie or Food Chop), and the blender will cycle through
that program delivering professional results every time.
14. When using a Pre-Programmed Setting, the blender will automatically
stop when the program is finished. The blinking green light indicates that
the blender is ready for use.
15. Press the Power Button to turn the blender off.
16. To Pulse, push and hold down the Pulse Button for the desired length of
time. Release and allow blade to stop. Repeat cycle
as desired.
Blending Tips
Put liquids in the Blender Jar first, unless a recipe
•
says otherwise.
• Crushing ice: Crush 6 ice cubes or approximately
2 cups of ice. Cover ice with about 1 cup or 0.236
liters of water for best results.
• Do not remove the Blender Lid while in use. Remove Filler Cap to add
smaller ingredients. (Figure 7)
• Cut all firm fruits and vegetables, cooked meats, fish and seafood into pieces
no larger than 3/4 inch (1.9 cm) to 1 inch (2.5 cm). Cut all kinds of cheeses
into pieces no larger than 3/4 inch (1.9 cm).
• This Blender will not mash potatoes, whip egg whites or substitute dairy
toppings, mix stiff dough or grind raw meat.
I C
Ce rushIng
Without Liquid: Use Pulse button until you achieve desired results.
With Liquid: Add desired amount of ice cubes and water until ice floats. Blend on
High until you achieve desired results then strain off water.
BLSTPDG-GD0-000_23ESM1.indd 6-7 BLSTPDG-GD0-000_23ESM1.indd 6-7
F 7
igure
6
Hot Foods
• Open the Filler Cap to vent steam. Tilt Filler Cap away from you. Keep
hands away from the cover opening to prevent possible burns.
• When working with hot liquids, remove Filler Cap and start blending at
a low speed. Then move to a faster speed. DO NOT add liquid over the
4 cup (0.946 liter) level.
Cleaning Your Blender
WARNING: Unplug before cleaning. Do not immerse the blender base in
water or any other liquid.
Use a damp, soft sponge with mild detergent to clean the outside of the
Blender Base. All parts except for the Blender Base are dishwasher-safe. Place
Sealing Ring in bottom basket of dishwasher. You can also wash the parts in
warm, soapy water. Rinse well and dry.
e C F
asY lean eature
Quickly and conveniently clean Blender Jar between uses without removing
the blade from the jar.
• Pour 3 cups (0.709 liter) of warm water in the blender Jar.
Add 1 – 2 drops of liquid dishwashing detergent.
•
Select Low speed.
•
• Run blender for 20-30 seconds then press Power button.
Empty jar of soapy water into sink and rinse the Blender Jar thoroughly with
•
clean water.
NOTE:
Easy clean is not a substitute for regular cleaning described in the "Cleaning Your
Blender" section above. It is especially important to disassemble and thoroughly
clean your blender when processing milk, meats, seafood, and eggs.
NOTE:
This appliance has no user serviceable parts. Any servicing beyond that
described in the Cleaning Section should be performed by an Authorized Service
Representative only. See warranty available online.
Storing Your Blender
After cleaning and drying, reassemble Blade System to Blender Jar with Sealing
Ring and Blender Jar Bottom Cap. Store Blender with cover ajar to prevent
container odor.
7
2023/8/28 11:01 2023/8/28 11:01