Blackstar Amplification ID:CORE STEREO 10 V4 Manual Del Propietário página 10

Advanced Features
Your ID:CORE amplifier has further advanced features which are aimed at more in-
depth users who enjoy getting the most from their amplifier. These features do not
have independent controls on the front panel of the amplifier, but instead are accessed
by using the Tap switch (11) as a 'shift key' and using other controls to access these
features.
Independent Music Playback Volume – Tap + Volume
Under most circumstances, the volume of your music playback via the MP3/Line Input
is effectively controlled directly from your playback device. For quieter environments
and general convenience you can also further reduce the music playback volume of
your ID:CORE amplifier by simply holding down the Tap switch (11) whilst turning the
Volume control (4) on the front panel.
USB Recording Level – Tap + Gain
As stated in the USB Audio section (see page 15), the output level of the USB audio
signal from your ID:CORE amplifier can be controlled independently of your amplifier's
speaker volume by holding down the Tap switch (11) whilst turning the Gain control
(3) on the front panel.
Effect Speed/Time – Tap + Effects Level
As stated in the Effect Level section (see page 10), the speed/time of the modulation
and delay effects can be controlled by holding down the Tap switch (11) whilst turning
the Effect Level control (10) on the front panel. This can be very useful for setting a
specific accurate effect tempo instead of using the Tap switch.
Firmware Update
Firmware updates are initiated via the Blackstar ARCHITECT software. A new version
of the Blackstar ARCHITECT software will be released whenever an update is available.
Important note: Always connect the amplifier to a main USB port (usually found on the
on the rear of your PC or Mac) when updating the firmware. Never use a front mounted
USB port, USB hub or a USB extension cable. Doing so may result in a failed update,
which could cause your amplifier to become unresponsive.
When the amplifier is connected (via USB) to a version of the Blackstar ARCHITECT
software containing newer firmware, a message will be displayed prompting you to
install the latest files. Whilst updating, the amplifier controls will be unresponsive. Front
panel voice LEDs will cycle to indicate data activity during the update process.
The amplifier power should not be switched off during a firmware update. If the
amplifier is switched off during an update, the controls may be unresponsive after the
power is reapplied and the amplifier will produce no sound. The voice LEDs will cycle
to indicate that the amplifier contains no valid firmware.
If you are experiencing problems with the firmware update process the amplifier can be
forced to power up in Update Mode. Hold down the Manual (14) & MOD (6) switches
simultaneously, whilst switching on the amplifer to enter this mode with the voice LEDs
cycling to indicate Update Mode. Connect the amplifier to the Blackstar ARCHITECT
software to begin a firmware update.
The amplifier must be connected to the Blackstar ARCHITECT software to
reinstall valid firmware. The update process will start automatically if the Blackstar
ARCHITECT software detects that the amplifier is in this state.
18
Technical Specification
ID:CORE STEREO 10 V4
Power: 10 Watts
Speaker: 2 x 5 Watts
Weight (kg): 3.7
Dimensions (mm): 340(W) x 265(H) x 185(D)
ID:CORE STEREO 10 V4 Bluetooth
Power: 10 Watts
Speaker: 2 x 5 Watts
Weight (kg): 3.7
Dimensions (mm): 340(W) x 265(H) x 185(D)
ID:CORE STEREO 20 V4
Power: 20 Watts
Speaker: 2 x 10 Watts
Weight (kg): 5.2
Dimensions (mm): 375(W) x 292(H) x 185(D)
Footswitch (not supplied): FS-11, FS-18 or FS-22 footswitch
ID:CORE STEREO 40 V4
Power: 40 Watts
Speaker: 2 x 20 Watts
Weight (kg): 6.2
Dimensions (mm): 434(W) x 336(H) x 185(D)
Footswitch (not supplied): FS-11, FS-18 or FS-22 footswitch
19