Blackstar Amplification ID:CORE STEREO 10 V4 Manual Del Propietário página 8

4. Press record to test your levels are loud and clear. Use the channel 'Gain' controls
on your amplifier to set the level sent to your phone.
5. Test and adjust your channel controls and effects for optimum sound on your
Blackstar amplifier.
6. Record High quality videos, Audio memos and Livestream (direct to Instagram
Live, Facebook, YouTube, Twitch and more) straight from your amplifier.
17. CabRig™ & Phones
CAB RIG LITE is a next-generation advanced speaker simulator that reproduces the
sound and feel of guitar speaker cabs in incredible detail.
This output also emulates the tonal characteristics of a guitar speaker cabinet and
provides a natural tone for connection to headphones, a recording device, PA
system or mixing desk.
To make full use of the Super Wide Stereo effects, use a 'Stereo 3.5mm jack to two
Mono Jacks' splitter lead to feed two channels of the recording device or mixer.
Always use a good quality screened lead.
Turning the Volume knob will control the Emulated Output level.
NOTE: The Amplifier speakers will mute when a cable is connected to the CabRig™
& Phones jack.
18. Recall Indicator
The Recall Indicator shows if there is a mismatch between the current value of a
parameter within the amplifier and the corresponding physical front panel control.
For example, when you change to a different patch the controls on the front panel
may not always reflect the setting you are hearing.
To prevent unexpected level jumps in the control you are adjusting, the front panel
knobs will have no effect on the sound until the knob reaches the current parameter
value. Once reached the Recall Indicator flashes twice and the knob 'takes control'
of the value and can increase or decrease the value.
The recall indicator will flash each time the physical knob 'passes through' the
currently active value that you are hearing.
Recall is active for Gain, Volume and ISF.
When the Tuner is active the Recall Indicator will flash continuously.
19. Power Reduction
The Power Reduction button allows the user to reduce the output stage from full
power down to 1W without sacrificing tone:
Full Power - This is the full power setting which will give the loudest clean headroom.
1W - This is the low power setting which reduces the output down to 1 Watt. Use
this when lower volumes for practise and recording are desired.
14
20. Bluetooth connectivity (ID:CORE V4 10 Bluetooth only)
Your ID:CORE V4 10 Bluetooth amplifier is equipped with Bluetooth connectivity
for wirelessly streaming your favourite music in Super Wide Stereo. The custom
designed speakers and acoustically tuned cabinet reproduce your music with
incredible hi-fi sound quality, from crisp, clear highs to deep, punchy lows. Press
this switch to pair a Bluetooth device to your ID:CORE V4 10 Bluetooth amplifier
and toggle between the modes of operation (see below). When the Bluetooth LED
is unlit the Bluetooth connectivity is not active.
Discoverable Mode (slow LED flash)
To connect a Bluetooth device to your ID:CORE V4 10 Bluetooth for the first time
you must make a 'pairing' between the two devices. To pair, simply press the
Bluetooth switch on your ID:CORE V4 10 Bluetooth amplifier until the Bluetooth
LED displays a slow flash. In this state other Bluetooth devices are able to 'see' your
ID:CORE V4 10 Bluetooth amplifier (hence the term 'Discoverable') and can make
a request to pair.
Whilst the Bluetooth LED is flashing slowly, go to the Bluetooth Settings page of
your Bluetooth device and look for your ID:CORE V4 10 Bluetooth amplifier in the
list of available devices. Your amplifier will be identified as 'ID V4 XX:XX', where
XX:XX is the last four characters of your amplifier's unique ID. When 'ID V4 XX:XX'
appears, simply select this device and wait a few moments for the pairing to be
made. You will hear an audible tone from the amplifier to indicate that a device has
been successfully connected.
If a pairing has not been made within the Discoverable Mode timeout window, the
Bluetooth connectivity will switch off and will wait for user input in order to attempt
a new pairing. Simply press the Bluetooth switch again to enter Discoverable Mode
again and restart the pairing process.
Pressing the Bluetooth switch while in Discoverable Mode will set your ID:CORE V4
10 Bluetooth amplifier to Scanning Mode.
Scanning Mode (fast LED flash)
Scanning Mode is used to reconnect any previously paired Bluetooth devices to
your ID:CORE V4 10 Bluetooth if they have travelled out of range or have been
disconnected. Ensure your previously paired Bluetooth device has Bluetooth
connectivity switched on and enter Scanning Mode; your amplifier will 'scan' for
previously paired devices within range and attempt to reconnect, starting with the
device that was most recently connected. You will hear an audible tone from the
amplifier to indicate that a device has been successfully reconnected.
If you have previously paired any Bluetooth Devices to your ID:CORE V4 10 Bluetooth
amplifier it will power on in Scanning Mode. If your Bluetooth device is within range
and has Bluetooth connectivity switched on, your amplifier will automatically
reconnect to your device, allowing you to start streaming your music straight away.
Pressing the Bluetooth switch from Scanning Mode will set your amplifier to
Discoverable Mode in order to begin pairing a new device.
At any time, you may disconnect your Bluetooth device from your amplifier by either
pressing and holding the Bluetooth switch on the amplifier front panel or switching
off the Bluetooth functionality of your device. You will hear an audible tone from the
amplifier to indicate that a device has been disconnected.
Performing a Factory Reset will clear the amplifier's memory of previously paired
Bluetooth devices. You will need to repeat the pairing process with any devices you
wish to reconnect.
15