Silvercrest SDBK 2400 E1 Guía Rápida página 20

3 . Carefully pour water into the water tank . Do not exceed
the max mark
.
[ 13 ]
4 . Close the lid of the fill opening
Spray function
You can spray the fabric in front of the soleplate
o
water as required . To do so, press the spray button
Steam burst
You can steam the fabric through the soleplate
o
required . To do so, press the steam burst button
NOTES:
You can also use the steam burst in a
o
vertical position .
The higher the set temperature, the stronger the steam
o
burst .
Steam ironing
You can also set the iron to continuously give off steam .
o
The temperature control
o
to produce enough steam .
The steam control has 3 positions:
[ 3 ]
o
No Medium
steam
NOTE: Continuous steam ironing is only possible when
the iron is held horizontally . If you hold the iron vertically
or set it down, this interrupts steam operation .
˜ Ending ironing
1 . Turn the temperature control
way to MIN .
2 . Set down the product with the stand base
stable surface .
3 . Disconnect the power plug
4 . Let the product cool (this takes approximately
15 minutes) . Do not leave the product unattended while
it is still hot .
5 . To prevent limescale build-up, empty the water tank after
each use . To do so, open the lid of the fill opening
Empty the water tank via the fill opening by holding the
iron upside down over a sink .
˜ Additional product features
˜ Anti-drip system
The product features an anti-drip system . This prevents
o
water from exiting from the soleplate
temperature is too low to produce steam . This feature
prevents water stains on your clothing .
20 GB/IE
.
2 ] [
with
[ 14 ]
4 ] [
as
[ 14 ]
.
[ 5 ]
should be at the highest level
[ 11 ]
Maximum
steam steam
counter-clockwise all the
[ 11 ]
on an even,
10 ] [
from the power outlet .
[ 8 ]
2 ] [
as long as the
[ 14 ]
˜ Anti-lime filter
The product features an anti-lime filter . This is a
o
permanent water filter . It is not in need of replacement or
maintenance .
To maintain the filter's functionality, only fill the water tank
o
with tap water or distilled water .
Do not use any additives . They may damage the water
.
o
filter .
˜ Cleaning and care
m
DANGER! Risk of electric shock! Always disconnect
the plug from the power outlet before cleaning the
[ 8 ]
product .
m
WARNING! Do not immerse the product's electrical
components in water or other liquids . Never hold the
product under running water .
Wipe down the product with a slightly damp cloth .
o
Do not let any water or other liquids enter the product
o
interior .
Do not use any abrasive, aggressive cleaners or hard
o
brushes to clean the product .
Clean the soleplate
o
non-scouring detergent .
Let all parts dry completely after cleaning .
o
˜ Self-cleaning function
The product features a self-cleaning function to remove
o
filth and limescale build-up in the steam channels .
Use the self-cleaning function at least twice per month .
o
If you use tap water: Use the self-cleaning function after
o
every use .
NOTE: Check the hardness of your household's water
with your local water supplier .
m
DANGER! Risk of electric shock! Always unplug the
power plug
[ 8 ]
1 . Never fill the water tank past the max mark
so, open the lid of the fill opening
2 . Place the product on the stand base
and are aligned (Fig . C) .
3 . Turn the temperature control
way to MIN .
4 . Plug the power plug
.
5 . Set the temperature control
(turn clockwise all the way) .
6 . Set the steam control
7 . Wait for the product to heat up and the temperature
control lamp
6 ] [
8 . Hold the product horizontally over a sink .
9 . Press and hold the self-cleaning button
steam or boiling, soiled water exits the product .
10 . Empty the water tank of any residual water via the fill
opening .
2 ] [
using a damp cloth and a mild,
14 ] [
before filling the water tank .
.
[ 2 ]
. Make sure
[ 10 ]
counter-clockwise all the
[ 11 ]
into an appropriate power outlet .
[ 8 ]
to the highest temperature
[ 11 ]
to maximum steam power .
[ 3 ]
to go off .
until no more
12 ] [
. To do
13 ] [