Publicidad
Idiomas disponibles
Idiomas disponibles
ORANGE LIGHT: Room conditions far
from optimal level.
GREEN LIGHT: Most people feel good
room conditions, near optimal level.
BLUE LIGHT: Best comfort level.
Perfect!
•
In particularly severe environmental conditions (large size
room, high temperature or humidity outside, poor insula-
tion of the room, too many of people or strong heat load
in the room, strong exposure to the sun ...) this device may
not be able to reach the best comfort level.
ARCTIC WHISPER EXTREME (available in air condition-
ing mode only)
By activating this function, the operating noise is further
reduced. To activate, touch the
control. The display shows the related symbol (C12).
SWING FUNCTION
This function moves the flap, evenly distributing the air into the
room.
When the
Swing button (D5) is touched, the flap will begin
to move forwards and backwards alternatively.
If touched again, the flap will be locked into its current position.
When the button is next touched, the flap will start to move for-
wards and backwards again.
Please note: in order to avoid damaging the internal mecha-
nisms, the flap must not be moved manually.
SETTING THE TIMER
The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optimizing
the operating periods.
How to program delayed shut down
•
While the appliance is ON in any operating mode, delayed
shut down can be programmed.
C17
C15
C8
C10
C14
C16
C3
C2
button (D6) on the remote
C17
C15
C8
C10
C14
C16
C3
C2
•
Touch the
timer button (D8): the timer symbol
(C15) and hours (C16) light up.
•
Touch the
(D3) and
number of hours to shut down appears on the display.
A few seconds after the timer is set, the setting is acquired, the
display shows the operating mode and the timer symbol stays lit.
C17
Once the set time is elapsed, the air conditioner goes into Standby.
C15
To cancel the timer program, touch the
C8
twice. The timer symbol (C15) will go off.
C10
Please note: Once the timer has been activated, by touching the
timer button only one time, the remaining hours to shut down
will be displayed.
C14
How to program delayed start up
C16
•
Plug in the appliance and set to standby.
•
Touch the
timer button (D8): the timer symbol (C15)
and hours (C16) light up.
C3
•
Touch the
(D3) and
number of hours to start up appears. Start up can be pro-
C2
grammed at any time within the 24 hours that follow.
When the set time is elapsed, the appliance will start to operate
in the same operating mode that was previously set.
To cancel the timer program, touch the timer button (D8) twice.
The timer symbol (C15) will go off.
Please note: Once the timer has been activated, by touching the
timer key only one time, the remaining hours to the start up will
be displayed.
REPEAT PAIRING OF CST REMOTE CONTROL
The CST remote control is already pair to this DeLonghi Pinguino
appliance. In case you want to pair with another DeLongi Pin-
guino device, or in case of a pairing of brand new CST remote
control, the user needs to put the unit in Standby mode and
touch for 10 seconds the MODE selection button (D2) on the CST
remote control. The LED (D10) starts blinking periodically indi-
cating the pairing phase.
Then, press for 10 seconds the MODE button (C2) on the Pinguino
unit until a double beep is emitted. The pairing phase is signaled
on display by means of a fast flashing of the dot in the middle
of the digits.
When the two devices complete the pairing dialogue, the PAC
emits a double 'beep' . The display will return to as it normally
10
C5
C6
C7
C9
C12
C13
C11
C4
(D4) buttons until the desired
C1
C5
C6
C7
timer button (D8)
C9
C12
C13
C5
C6
C11
C7
C9
C4
(D4) buttons until the desired
C12
C1
C13
C11
C4
C1
Publicidad
