cecotec Bolero DressCode 9410 Inverter Steel A Manual De Instrucciones página 32

ENGLISH
23. Delay indicator light
24. Child Lock indicator light
25. Door lock indicator light
26. Mute indicator light
27. Spin speed (rpm) indicator lights
28. Temperature (ºC) indicator light
29. Display
30. Soaking cycle indicator light
31. Washing cycle indicator light
32. Rinse cycle indicator light
33. Spin cycle indicator light
Detergent drawer. Fig. 3
1. Detergent compartment (II)
2. Softener compartment
Note:
The graphics in this manual are schematic representations and may not exactly match the
appliance.
2. BEFORE USE
- This appliance is packaged in a way as to protect it during transport. Take the device out
of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the device when
transporting it in the future. In case the original packaging is disposed of, make sure all
packaging materials are recycled accordingly.
- Make sure all parts and components are included and in good conditions. If there is any
piece missing or in bad conditions, contact the Official Cecotec Technical Support Service
immediately.
Box content. Fig. 4
1. Washing machine
2. Inlet hose
3. Drain hose
4. Cover for transport bolt holes (x4)
5. Drain hose bracket (NOT included with some models)
6. Spanner (NOT included with some models)
7. Instruction manual
62
Bolero Dresscode 7410 Inverter A / Bolero DressCode 7410 Inverter Steel A
Bolero Dresscode 8410 Inverter A/ Bolero DressCode 8410 Inverter Steel A
Bolero Dresscode 9410 Inverter A/ Bolero DressCode 9410 Inverter Steel A
Bolero Dresscode 10410 Inverter A/ Bolero DressCode 10410 Inverter Steel A
3. INSTALLATION
Please note
It is recommended that your new washing machine is installed by a qualified technician. If
you think you're able to install the washing machine, please read the installation instructions
carefully before proceeding with installation.
Needed tools
It is recommended that you have the following tools to facilitate the installation of the washing
machine: scissors, pliers, standard screwdriver, gloves, and spanner.
Unpacking the washing machine
Unpack the washing machine and check if it has suffered any damage during transport. Should
the machine be damaged or any items missing, please contact your local retailer immediately.
Choosing the location for installation
- Choose an installation location that complies with the following characteristics:
- Rigid, dry, and level surface (if not level, please read the "Levelling the washing machine"
section).
- No direct sunlight.
- Properly ventilated.
- Ambient temperature between 0 and 40 °C.
- Ambient humidity below 95% (when the temperature is 25 °C).
- Keep the washing machine away from heat sources such as coal or gas. Make sure the
washing machine is not crushing the power cord. Do not install the washing machine on
carpeted floors.
Removing the transport bolts. Fig. 5
Before using the washing machine, remove the transport bolts from the back of the appliance.
To do so, follow the below steps:
1. Loosen the four transport bolts.
2. Grab the bolts by the head and pull them out.
3. Fit the plastic caps into the holes of the transport bolts.
4. Store the transport bolts in a suitable place for future use.
Levelling the washing machine
Fig. 6 key:
A. Structure of the levelling feet:
1. Lock nut
2. Rubber base
Bolero Dresscode 7410 Inverter A / Bolero DressCode 7410 Inverter Steel A
Bolero Dresscode 8410 Inverter A/ Bolero DressCode 8410 Inverter Steel A
Bolero Dresscode 9410 Inverter A/ Bolero DressCode 9410 Inverter Steel A
Bolero Dresscode 10410 Inverter A/ Bolero DressCode 10410 Inverter Steel A
ENGLISH
63