Beninca BEVA.5 Manual De Instrucciones página 20

INDEX
1) DESCRIPTION .......................................................................................................................................................................................................................................................... 23
2) DIMENSIONS........................................................................................................................................................................................................................................................... 23
3) OPENING 24
4) LEFT-RIGHT BARRIER (FIG. 3/4) .............................................................................................................................................................................................................................. 24
5) EMERGENCY MANUAL OPERATION (FIG.5) ............................................................................................................................................................................................................... 25
6) INSTALLATION OF THE OPTIONAL FOUNDATION PLATEVE.PS (FIG.6) ....................................................................................................................................................................... 25
7) POSITIONING OF THE SPRING AND ACCESSORIES (FIG.7)......................................................................................................................................................................................... 25
8) HOW TO FIX THE BEAM (FIG.8) ................................................................................................................................................................................................................................ 25
9) BALANCING (FIG.10)................................................................................................................................................................................................................................................ 25
10) HOW TO ADJUST THE MECHANICAL STOPPERS (FIG.13) ........................................................................................................................................................................................ 25
11) WIRE DIAGRAM (FIG.14) ........................................................................................................................................................................................................................................ 25
12) CP.EVA2 CONTROL UNIT ........................................................................................................................................................................................................................................ 26
12.1) WIRE DIAGRAM ........................................................................................................................................................................................................................................... 26
12.2) PROGRAMMING .......................................................................................................................................................................................................................................... 26
12.2.1) TO ACCESS PROGRAMMING ............................................................................................................................................................................................................. 26
12.2.2) PROGRAMMING NOTES .................................................................................................................................................................................................................... 26
12.2.3) QUICK PROGRAMMING ..................................................................................................................................................................................................................... 27
12.3) PARAMETERS, LOGICS AND SPECIAL FUNCTIONS ....................................................................................................................................................................................... 27
12.4) SYNCHRONIZATION OF TWO OPPOSED BARRIERS ....................................................................................................................................................................................... 30
12.5) TRANSMITTERS REMOTE LEARNING ........................................................................................................................................................................................................... 31
12.6) FUSES ........................................................................................................................................................................................................................................................ 31
12.7) BACK UP BATTERIES ................................................................................................................................................................................................................................... 31
12.8) DIAGNOSTICS ............................................................................................................................................................................................................................................. 31
12.9) ERROR MESSAGES ..................................................................................................................................................................................................................................... 31
13) WASTE DISPOSAL ................................................................................................................................................................................................................................................. 31
ENG
The product shall not be used for purposes or in ways other than those for which the product is intended for and as described in this manual.
Incorrect uses can damage the product and cause injuries and damages.
The company shall not be deemed responsible for the non-compliance with a good manufacture technique of gates as well as for any de-
formation, which might occur during use. Keep this manual for further use.
This manual has been especially written to be use by qualified fitters.
Installation must be carried out by qualified personnel (professional installer, according to EN 12635), in compliance with Good Practice and
current code. Make sure that the structure of the gate is suitable for automation.
The installer must supply all information on the automatic, manual and emergency operation of the automatic system and supply the end
user with instructions for use.
Packaging must be kept out of reach of children, as it can be hazardous. For disposal, packaging must be divided the various types of
waste (e.g. carton board, polystyrene) in compliance with regulations in force. Do not allow children to play with the fixed control devices of
the product. Keep the remote controls out of reach of children. This product is not to be used by persons (including children) with reduced
physical, sensory or mental capacity, or who are unfamiliar with such equipment, unless under the supervision of or following training by
persons responsible for their safety. Apply all safety devices (photocells, safety edges, etc.) required to keep the area free of impact, crushing,
dragging and shearing hazard. Bear in mind the standards and directives in force, Good Practice criteria, intended use, the installation en-
vironment, the operating logic of the system and forces generated by the automated system. Installation must be carried out using safety
devices and controls that meet standards EN 12978 and EN 12453.
Only use original accessories and spare parts, use of non-original spare parts will cause the warranty planned to cover the products to
become null and void. All the mechanical and electrical parts composing automation must meet the requirements of the standards in force
and outlined by CE marking.
An omnipolar switch/section switch with remote contact opening equal to, or higher than 3mm must be provided on the power supply mains.
Make sure that before wiring an adequate differential switch and an overcurrent protection is provided.
Pursuant to safety regulations in force, some types of installation require that the gate connection be earthed.
During installation, maintenance and repair, cut off power supply before accessing to live parts.
Also disconnect buffer batteries, if any are connected. The electrical installation and the operating logic must comply with the regulations
in force. The leads fed with different voltages must be physically separate, or they must be suitably insulated with additional insulation of at
least 1 mm. The leads must be secured with an additional fixture near the terminals.
During installation, maintenance and repair, interrupt the power supply before opening the lid to access the electrical parts
Check all the connections again before switching on the power. The unused N.C. inputs must be bridged.
WASTE DISPOSAL
As indicated by the symbol shown, it is forbidden to dispose this product as normal urban waste as some parts might be harmful for en-
vironment and human health, if they are disposed of incorrectly. Therefore, the device should be disposed in special collection platforms
or given back to the reseller if a new and similar device is purchased. An incorrect disposal of the device will result in fines applied to the
user, as provided for by regulations in force.
Descriptions and figures in this manual are not binding. While leaving the essential characteristics of the product unchanged, the manufacturer reserves
the right to modify the same under the technical, design or commercial point of view without necessarily update this manual.
20
WARNING