Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Press the DEHUMIDIFICATION button to set the humidity:
CO→40%→45%→50%→55%→60%→65%→70%→75%→80%, CO stands for
continuous dehumidification.
4.
1 Press the MODE button to set the mode to 1(Low)-2(Medium)-3(High)-Auto.
2 If the unit operates in fan mode only, press the button to set the fan level to
1(Low)-2(Medium)-3(High).
3 When the machine works continuously for 360hr, the display will show the P3
code to remind the user to clean the filter. Then press the button for 3 sec to
clean the P3 code, then the P3 code will disappear and the display will show the
current ambient temperature level.
5.
Press the SWING button to turn the swing function on/off
6.
Press the FAN button to turn the fan function on/off.
When the unit is in fan function, the user can press the SPEED button to set the
fan speed to 1(low)-2(medium)-3(high).
7.
Beep on/off button:
When the unit is operating, press the SWING and TIMER button for 3 sec to turn
the beep on or off.
8.
Humidity level indicator:
The LED-indicator is in the front casing of the unit.
When the humidity≤59%, the indicator lights green;
When the humidity is ≥60%, the lights illuminate orange;
When the humidity is ≥70%, the lights illuminate red.
WATER TANK FULL ALERT
When the unit's water tank is full, a signal will be emitted for 10 times and the water-full
indicator light will come on. The unit will then stop working immediately. Make sure the
water tank is emptied and placed back into the unit correctly. The unit will then resume
operating in its last set mode.
MEMORY FUNCTION
(1) When the appliance is switched off and it is then in standby mode, it will remember
the last setting and it will start up when the appliance is switched on again.
(2) If the power fails while the appliance is switched on, the appliance will also remember
the last setting for when the power is switched on again.
(3) When the child lock and timer are set, the appliance switches off when the time has
elapsed. At that time, the appliance will not remember the child lock for when it is set
again, it will have to be reactivated.
SYNC MOTOR FAILURE
When Sync motor failure, the unit will show C4. The Main motor, Sync motor and hot air
motor will stop working after 10mins.
4
58
58
Error code
Reason
NTC1 is open cut or short cut
C1
NTC 2 is open cut or short cut
C2
NTC1 &NTC 2 are open cut or short cut
C3
Sync motor is failure
C4
Pre-filter clean notice
P3
Temperature and humidity sensor is failure
88
PROTECTION AGAINST FALLING OVER
The machine has a heater inside. To prevent overheating, the machine is equipped with
a tilt switch that automatically switches off if the machine falls over.
CONTINUOUS DRAINAGE FUNCTION
The dehumidifier has a continuous drain hole that can be connected to a plastic pipe
of 2m long. The water can be drained into a sink or larger container. This unit uses
gravity to drain the collected water and therefore the drain should be lower than the
dehumidifier's water outlet. Make sure that the drain pip runs down and allows the
water to flow out smoothly. Do not kink or bend the pipe."
CLEANING THE FILTER
The air intake can easily collect dust, so clean it regularly with a soft, damp cloth. If the
filter is covered with dust, the airflow and performance of the unit will be affected. It
may even cause damage to the unit. We recommend cleaning the filters regularly. The
dehumidifier must be unplugged before maintenance and the filters must be completely
dried before use.
1) Remove the filters from the unit and pat away the dust.
2) Clean the mesh filter with a hoover or soft brush.
If dirt and grease have accumulated, wash the mesh filter in hot soapy water.
3) This should dry thoroughly before replacing the filter in the appliance."
MAINTANANCE
• Do not place the appliance in direct sunlight as the housing is made of plastic.
• Remove the water tank carefully. Do not use alcohol, petrol or other benzene-
containing chemical solvents to clean the appliance.
• Keep the filter clean: remove the filter, then use a hoover or water to clean it, then put
it in a ventilated place until it is dry.
• Unplug the appliance before cleaning or performing other maintenance work.
• Turn off the appliance, unplug the power cord and remove the water from the tank
before putting the appliance away.
• If you are not going to use the appliance for a long time, switch it off, unplug it, empty
the water tank and wait 2 days to ensure the appliance is completely dry inside before
packing it away. Then make sure the appliance is stored upright. Do not place the
appliance horizontally or upside down.
• If the appliance needs repair. Enlist the help of after-sales service or another
professional person. We are not responsible for accidents or damage caused by
repairing the appliance yourself.
4
59
59
Publicidad
