EINHELL GP-CT 36/35 Li BL Manual De Instrucciones Original página 22

5.8 Installing the battery
Push the rechargeable batteries into the batte-
ry mounts provided on the left and right on the
equipment (Fig. 1/Item 1). The battery will be
heard to click into place when it has been pushed
fully in (Fig. 12). To take out the battery, press the
pushlock button (Fig. 12/Item C) and remove the
battery.
5.9 Charging the battery (Fig. 13)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The green LED
will then begin to fl ash.
3. Insert the battery pack into the battery char-
ger.
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Anl_GP_CT_36_35_Li_BL_SPK13.indb 22 Anl_GP_CT_36_35_Li_BL_SPK13.indb 22
GB
5.10 Battery capacity indicator (Fig. 14)
Press the switch for the battery capacity indicator
(Item B). The battery capacity indicator (Item A)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Danger! The guard hood must be fi tted when
carrying out work.
6.1 Switching the equipment on and off ,
adjusting the speed
6.1.1 Adjusting the speed (Fig. 12)
Warning! Set the speed only when the motor is
at a standstill.
Push the switch (Item 13) into position "1" =>
Low speed, longer battery running time. Push the
switch (Item 13) into position "2" => High speed,
shorter battery running time.
6.1.2 Switching on
Press the left or the right safety lock-off (Item 4)
and the On/Off switch (Item 3). Once the tool is
running, you can release the safety lock-off .
Note: When you switch on in switch position "2",
the motor might start up at a slightly reduced
speed and not reach maximum speed until it is
placed under load. This is not a fault.
- 22 -
02.05.2023 09:49:52 02.05.2023 09:49:52