HIKOKI C 12RSH3 Instrucciones De Manejo página 17

Compound Bevel (Right)
Cutting Angle 0°–45°
LED light
Machine Dimensions (Width x
Depth x Height)
Net weight* 2
*1 Be sure to check the nameplate on product as it is
subject to change by areas.
*2 According to EPTA-Procedure 01/2014
Table 1: Max. sawing dimension
Head
Miter 0
Left 45°
Bevel
Right 45°
Left 45°
Compound
Right 45°
PRIOR TO OPERATION
WARNING
Make all necessary adjustments before inserting the
plug in the power source.
1. Power source
Ensure that the power source to be utilized conforms to
the power requirements specified on the product
nameplate.
Do not use with direct current, or transformers such as
boosters. Doing so may result in damage or accidents.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Remove all packing materials attached or
connected to the tool before attempting to operate
it.
5. Installation (Fig. 3)
Ensure that the machine is always fixed to bench.
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
Bolt length should be at least 40 mm plus the thickness
of the work bench.
For example, use 8 mm × 65 mm bolts for a 25 mm
thick work bench.
Miter (Right) 0°–45°, (Left) 0–45°
Yes
655 mm x 873 mm x 724 mm
25.5 kg
Max. sawing dimension
Turntable
Max. height Max. width
0 105 mm
Left 45°
or 105 mm
Right 45°
Right 57° 105 mm
0 68 mm
0 43 mm
Left 45° 68 mm
Right 45° 68 mm
Left 45° 43 mm
Right 45° 43 mm
6. Base holder adjustment (Fig. 4)
Loosen the 6 mm bolt with the 10 mm box wrench.
Adjust the base holder until its bottom surface contacts
the bench or the floor surface.
After adjustment, firmly tighten the 6 mm bolt.
7. Releasing the locking pin (Fig. 5)
When the power tool is prepared for shipping, its main
parts are secured by a locking pin.
Press the handle slightly down and pull out the locking
pin to disengag the cutting head.
During transport, lock the locking pin into the gear case.
8. Installing the dust bag, sub table assembly,
stopper and vises (The stopper is an optional
accessory.)
(1) Installing the dust bag (Fig. 6)
Install the dust bag onto the dust port on the miter saw.
Fit the connecting tube of dust bag and the dust port
together.
To empty the dust bag, pull out the dust bag assembly
312 mm
from dust port. Open zipper on underside of bag and
empty into waste container. Check frequently and
empty the dust bag before it gets full.
220 mm
When bevel angle cutting, adjust the support bar and
Install the dust bag so that it hangs down vertically.
170 mm WARNING
Do not use this saw to cut and/or sand metals. The hot
312 mm
chips or sparks may ignite saw dust from the bag
material.
312 mm
CAUTION
○ Empty the dust bag frequently to prevent the duct and
220 mm
the lower guard from becoming clogged.
Sawdust will accumulate more quickly than normal
220 mm
during bevel cutting.
○ After cutting wood, before starting to cut aluminum
220 mm
window sash, discard the chips that are in the dust bag.
220 mm (2) Installing the sub table (Fig. 7)
Using an item such as a steel square, match the upper
surfaces of the base surface and sub table. Adjust the
vertical level of the sub table by turning the 8 mm height
adjustment bolt. After the adjustment, secure the holder
with the 8 mm bolt on the rear of the base, and secure
the 6 mm knob bolt of the sub table.
(Attach the vise assembly as shown in Fig. 1 and also
stopper as shown in Fig. 19.)
9. Check the lower guard for proper operation
(Fig. 35)
WARNING
NEVER OPERATE THE POWER TOOL if the lower
guard does not function smoothly.
Lower guard is designed to protect the operator from
coming into contact with the saw blade during operation
of the tool.
Always check that the lower guard moves smoothly and
covers the saw blade properly.
10. Oblique angle
WARNING
When changing the oblique angle, hold down the motor
head. If the motor head moves to an oblique angle
suddenly, it may result in injury or damage to the main
body.
Before the power tool is shipped from the factory, it is
adjusted for 0°, right angle, left 45° bevel cutting angle
and right 45° bevel cutting angle with the 8 mm set
screws.
When changing the adjustment, change the height of
the 8 mm set screws by turning them. (Fig. 8-a,
Fig. 8-b)
When changing the bevel angle to the left 45°, loosen
the 6 mm wing bolt shown in Fig. 12, then slide the sub
fence (B) outward and incline the motor head to the left.
17
English