Goizper Group IK Window tinting & PPF Manual Del Usuario página 4

SETTING UP
2
A. Assembly
1) Connect the hose (1369) to the bottom of the tank (1171) (Figure 1).
2) Thread one end of the handle onto the hose and attach the nozzle to the other end (Figure 1).
B. Verifi cation
1) Pay special attention to the hose connections (Figure 2).
2) Infl ate the vacuum sprayer up to a 2 bar / 30 psi pressure (Figure 3).
3) The pressure must not drop lower than 0,5 bar / 8 psi in a 30 minute period (Figure 4).
4) Pull the button on the safety valve (1348). The pressure must be released (Figure 15).
5) Pull the handle (1370). It must open and close (Figure 6).
C. Preparation and spraying
1) To unscrew the chamber press the pump handhold downwards and turn it counterclockwise (Figure 7).
2) Fill the tank up to the maximum level specifi ed for each model (Figure 8). Strongly screw the complete chamber (1344) in the tank.
3) Generate the desired pressure in the tank using strokes (Figure 9), the maximum pressure must not exceed 6 bar (the red stripe in the
pressure gauge) (1349), if the maximum pressure is exceeded the safety valve (1348) releases the excessive pressure (Figure 10). To
screw the chamber press the pump handhold downwards and turn it clockwise.
4) If you have access to compressed air, loosen the cap attached to the tank with an Allen key and securely fasten the air connector
(Figure 11). Connect the compressed air hose with a maximum pressure of 6 bar and insert it into the tank connector (Figure 12). Do
not remove the safety valve under any circumstances.
3
MAINTENANCE
1) After each use, depressurise the sprayer (Figure 1).
2) Collect and dispose of the residual amount in accordance with the laws, regulations and applicable standards.
3) Clean the sprayer with water.
4) In the event of obstruction of the nozzle, clean it with water and do not use metallic objects (Figure 2).
5) To prolong the length of the life of the joints, regularly apply a few drops of oil or grease on the moving parts (Figure 3).
6) Store the chamber and tank separately indoors protected from frost and fi erce heat ((40°F & 85°F) between 5ºC and 30ºC).
4 TROUBLE SHOOTING
PROBLEM
Pressure is not generated in the sprayer
The liquid comes out of the top of the pump
The handle (1370) does not spray but there is
pressure
The safety valve (1348) excessively discharges
The pressure gauge (1349) does not indicate the
pressure in the tank
5 USES AND SECURITY REGULATIONS
1) Always follow the instructions and dosages on the packaging labels, that the manufacturer recommends for the chemical
product to be used.
2) To avoid any consumption of the product, do not eat, drink or smoke while preparing and spraying.
3) Do not spray on people, animals, electrical installations, fl ames, open fi re, or other sources of ignition.
4) In case of poisoning, consult your doctor, taking the chemical product packaging with you.
5) Never dispose of waste product or cleaning residues near water courses, wells, etc.
6) Use suitable safety equipment, mask, goggles, gloves, footwear etc in order to avoid contact of chemical products with
skin, eyes and mouth.
7) Read the instructions for the sprayer before its use. Do not modify the sprayer. Do not obstruct or strike the safety valve.
Do not use the sprayer if it is damaged, deformed or altered from its original shape. Store the sprayer protected from
frost and extreme heat (between 5ºC and 30º C (40ºF & 85ºF)). Should the hose, tank, handle or any of its connections
be damaged, do not attempt to repair but replace the items with new parts.
8) Keep sprayer out of reach of children.
9) Use the device only with compatible substances (Scope of Application).
10) The safety valve should not be removed.
11) Never purge nozzles or valves by blowing with your mouth.
12) Use only spare parts and accessories from the manufacturer.
13) We will not be held liable for any damage caused by the use of foreign parts.
14) In the event that the sprayer material come into contact with hydrogen peroxide or products with a similar oxygen release, pressure
may produce pressure surges and result in an explosion. Never use these types of products.
CAUSE
The pump is not properly screwed in enough
Defective pump o-ring (1345)
Defective seal collar (1346)
Defective or dirty non-return valve (1347)
The handle fi lter is obstructed
Defective safety valve
Defective pressure gauge
SOLUTION
Properly screw the pump
Replace the O-ring (Figure 1)
Replace the seal collar (Figure 1)
Clean or replace the non-return valve (Figure 2)
Loosen the fi lter holder and clean (Figure 3)
Replace the safety valve
Break the connection points of the window (top, right,
bottom), Turn the window and loosen the pressure
gauge using a wrench and change (Figure 4)